Évaluations - 2, GPA: 4.5 ( )

Fabricant : Stihl Taille : 766.45 kb Nom Fichier : Langue d'enseignement:

Re-install cover knobs and tighten securely. 10. Tighten the tension bolt until the indicator reaches the white line. Refer to chainsaw owner’s manual for the proper oil/gasoline ratio. Maintain an ample supply of bar and chain oil in the reservoir to lubricate the drive mechanism of the RIPSAW. 3 Dimension plate assembly Figure 1. Dimension plate assembly 1. Remove dimension plate and parts from box. 2. Slide guide arm under handle bracket with square pin facing downward. 3. Install and tighten handle to secure guide arm. 4. Remove T nut studs from dimension plate. 5. Slide T nut studs through slots in rear drive and idler plates, with the threaded stud pointing towards you. 6. Attach dimension plate by putting studs through holes in dimension tube. 7. Install Dimension plate nuts. 8. Slide guide finger onto guide arm (Figure 1) and tighten knob. 9. Adjust guide arm and finger to accommodate the size of each log you cut. 4 Text Box: RS000 18 (NOT SHOWN) PLASTIC PLATE Text Box: . . . Text Box: . Text Box: RS901 18 T NUT/STUD (2) Text Box: RS000 17 DIMENSION PLATE Text Box: RS000 16 DIMENSION TUBE Text Box: RS000 19 GUIDE ARM Text Box: RS999 22 DIMENSION NUT - DRIVE Text Box: RS000 15 HANDLE BRACKET Text Box: RS999 23 DIMENSION NUT - IDLER Text Box: RS000 20 GUIDE FINGER Text Box: RS800 02 DIMENSION PLATE HANDLE Text Box: RS800 19 GUIDE FINGER KNOB (1/4-28) Guide beam assembly TOP TOP ( 4 ) 500 31 000 49 SIDE VIEW 200 53 Figure 2. Guide beam assembly 1. Remove coupling clamp and other accessories from guide beam. 2. Install coupling clamp half way into guide beam with bushing.(Align set screws with holes.) 3. Lightly tighten the last setscrew to keep clamp from moving. 4. Place the end of the main guide beam onto clamp lining holes up with setscrews. 5. Secure guide beams by tightening all four setscrews. 6. Install proper support pin into bushing after placing beam on top of log. (The pin should not be above the top surface of the guide beam.) 7. Insert support pin knob and tighten it. Please note: Both the Guide Beams and End Clamps are made to be affixed on either the left or right side. It is imperative that you set up the machine with all of the knobs on the same side of the unit to avoid interference during the cutting process. 5 Text Box: RS000 46 SUPPORT PIN BUSHING Text Box: RS000 47 -2” SUPPORT PIN RS000 48 - 3” SUPPORT PIN Text Box: RS500 31 3/8-24X1-1/2 SET SCREW (4) Text Box: RS000 49 SUPPORT PIN KNOB Text Box: RS100 51 COUPLING CLAMP End clamp assembly 6 Text Box: RS000 57 Text Box: RS100 55 Text Box: RS800 15 Text Box: END CLAMP CLAMP EXTENDER END CLAMP BAR Front Drive Cover Front Idler Cover 7 Text Box: ROLL PIN Text Box: WASHER Text Box: BLADE GUARD SPRING Text Box: BLADE GUARD HANDLE Text Box: BLADE GUARD MOUNT Text Box: TRACKING BLOCK Text Box: RS000 03 FRONT TENSION ARM Text Box: RS800 17 COVER KNOB Text Box: BLADE GUARD ASSEMBLY RS000 01 TOP TUBE RS000 02 MAIN TUBE RS000 03 TENSION ARM-FRONT RS000 04 TENSION ARM.-REAR RS000 05 FRONT DRIVE COVER RS000 06 REAR DRIVE PLATE RS000 07 FRONT IDLER COVER RS000 08 REAR IDLER PLATE RS000 09 REAR DRIVE COVER RS000 10 REAR IDLER COVER RS000 11 LOCATING PIN RS000 12 HEX PIN RS000 13 PIVOT PIN RS000 14 AXLE RS000 15 HANDLE BRACKET RS000 16 DIM. PLATE TUBE RS000 17 DIMENSION PLATE RS000 18 DIM. PLATE PLASTIC RS000 19 GUIDE ARM RS000 20 GUIDE FINGER RS000 22 BLADE GUIDE BLOCK RS000 26 GUARD WIRE - DRIVE RS000 27 GUARD WIRE - IDLER RS000 28 GUARD WIRE MOUNT RS000 29 TENSION ASSEMBLY RS000 30 TENSION BOLT RS000 31 TENSION INDICATOR RS000 36 WHEEL SCRAPER - DRIVE RS000 38 BLADE GUARD PIVOT RS000 40 BLADE GUARD HANDLE RS000 42 END CLAMP RS000 46 SUPPORT PIN BUSHING RS000 47 SUPPORT PIN - 2" RS000 48 SUPPORT PIN - 3" RS000 49 SUPPORT PIN KNOB/STUD RS000 51 TRACKING BLOCK RS000 57 END CLAMP PIN RS000 59 GUIDE BEAM W/BUSHING RS000 60 MAIN GUIDE BEAM RS000 68 UPPER BLADE GUARD RS000 81 CLAMP EXTENDER RS001 01 DRIVE WHEEL RS001 02 IDLER WHEEL RS100 28 AXLE BUSHING RS100 37 BLADE GUARD ASSEMBLY RS100 51 COUPLING CLAMP RS100 52 COUPLING CLAMP SPACER RS100 53 COUPLING CLAMP BASE RS100 54 COUPLING CLAMP NUT BAR RS100 55 END CLAMP BAR W/BUSHINGS RS100 56 WHEEL SCRAPER - IDLER RS100 63 END CLAMP KNOB RS500 11 5/16 -18X1-3/4 COUPLING NUT RS500 12 /16 -18X3 SOC CAP BOLT RS500 14 1/4X3/4 ROLL PIN RS500 15 10-32/3/8 FLAT HD SCREW RS500 16 10-32/3/8 BUT SOC CAP SCREW RS500 17 1/4-28X1 SET SCREW W PATCH RS500 18 1/4-20X3/4 FLAT HD SCREW RS500 19 5/32X3/8 ROLL PIN RS500 20 1/4-20X1/2 HEX BOLT RS500 21 1/4-20X1-1/4 HEX BOLT RS500 22 1/4-20 HEX NUT RS500 23 10-32X1/4 PAN HD SCREW RS500 24 10-32X5/8 PHIL PAN HD SCREW RS500 25 10-32X5/16 PAN HD SCREW RS500 26 1/4-28X3/4 HEX BOLT RS500 27 10-32 KEP NUT RS500 28 1/4-20X5/8 HEX BOLT RS500 29 1/4 ID FLAT WASHER RS500 31 3/8-24X1-1/2 SET SCREW RS500 32 10-32X3/8 PHIL PAN HD SCREW RS500 33 1/4-20X1 SET SCREW RS500 34 3/8-16X2 SET SCREW RS500 35 1/4-20X1-1/4 SET SCREW RS500 36 1/4-28X1 SET SCREW RS500 37 3/16X3/8 RIVET RS500 38 BLADE G...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :