Évaluations - 5, GPA: 3.2 ( )

Fabricant : Desa Taille : 1.03 mb Nom Fichier : Langue d'enseignement:

Keep felling cut parallel to lower notch cut. 2. Cut towards notch. WARNING: Do not cut all the way through tree. Leave about two inches of tree diameter uncut directly behind felling notch (see Figure 11). This uncut portion acts as a hinge. The hinge helps keep tree from twisting and falling in wrong direction. Direction of Fall Figure 11 - Felling A Tree 2" 1st Cut - Lower Notch Cut 2nd Cut - Upper Notch Cut Hinge 2 Inches 3rd Cut - Felling Cut 3. As felling cut nears hinge, tree should begin to fall. Note: If needed, drive wedges into felling cut to control direction of fall. If tree settles back and pinches chain, drive wedges into felling cut to remove saw. Only use wedges made of wood, plastic, or aluminum. Never use wedge made of steel. This could cause kickback and damage to chain. 4. When tree begins to fall, quickly • remove saw from felling cut •release trigger to turn saw off • put saw down • exit area using retreat path WARNING: Be alert for falling overhead limbs. Watch your footing while exiting area. Continued 9 For more information, visit 10 107990 ELECTRIC CHAIN SAW ® For more information, visit BUCKING A LOG Figure 13 - Bucking Log With Entire Length On Ground WARNING: Avoid kickback. Kickback can result in severe injury or death. See Kickback, page 3 to avoid risk of kickback. WARNING: • If on slope, make sure log will not roll down hill. Secure log by using wooden stakes. Drive wooden stakes into ground on downhill side of log. Stand on uphill side of log while cutting. Log may roll after cutting. • Never try cutting through two logs at same time. This could increase the risk of kickback. • While cutting log, never hold log with your hand, leg, or foot. • While cutting log, never allow another person to hold log. • Turn off and unplug saw before moving from one place to another. Bucking a log is cutting a log into sections. Make sure your footing is firm. Keep feet apart. Divide your weight evenly on both feet. When possible, raise log or section off ground. Do this by using limbs, logs, chocks, etc. When cutting through log, maintain control by reducing cutting pressure near end of cut. Do not relax your grip on chain saw handles. Do not let moving chain touch ground. Ground will dull moving chain. After cutting through log, release trigger to turn saw off before moving saw. Follow directions below to buck a log. LIMBING A TREE Figure 12 - Limbing A Tree WARNING: When cutting limb that is under tension, use extreme caution. Be alert for wood springing back. When wood tension is released, limb could spring back and strike operator causing severe injury or death. WARNING: Avoid kickback. Kickback can result in severe injury or death. See Kickback, page 3 to avoid risk of kickback. Limbing is removing branches from a fallen tree. Make sure your footing is firm. Keep feet apart. Divide your weight evenly on both feet. Do not remove larger limbs under tree that support log off ground. Remove each limb with one cut (see Figure 12). Clear cut limbs from work area often. This will help maintain a safe work area. Make sure you start your cut where limb will not pinch saw during cutting. To avoid pinching, start cut on freely hanging limbs from above limb. Start cut on limbs under tension from under limb. If pinch occurs, turn saw off, lift limb, and remove saw. Entire Length Of Log On Ground Cut log from top (see Figure 13). Figure 14 - Bucking Log When Log Is Supported On One End 1st Cut 2nd Cut OPERATING CHAIN SAW Continued Log Supported On One End 1. Make first cut on underside of log (see Figure 14). Use top of guide bar to make this cut. Cut 1/3 through diameter of log. This cut will keep section from splintering when cut. 2. Make second cut directly above first cut. Cut down to meet first cut. This cut will keep log from pinching guide bar and chain. OWNER’S MANUAL OPERATING CHAIN SAW Continued Log Supported On Both Ends 1. Make first cut from above log (see Figure 15). Cut 1/3 through diameter of log. This cut will keep section from splintering when cut. 2. Make second cut on underside of log, directly under first cut. Use top of guide bar to make this cut. Cut up to meet first cut. This will keep log from pinching guide bar and chain. 1st Cut 2nd Cut Figure 15 - Bucking Log When Log Is Supported On Both Ends TRIMMING A TREE (Pruning) WARNING: Avoid kickback. Kickback can result in severe injury or death. SeeKickback, page 3 to avoid risk of kickback. Trimming a tree is the process of cutting limbs from a living tree. Make sure your footing is firm. Keep feet apart. Divide your weight evenly on both feet. Follow directions below to trim a tree. 1. Make first cut six inches from tree trunk on underside of limb. Use top of guide bar to make this cut. Cut 1/3 through diameter of limb (see Figure 16). 2. Move two to four inches farther out on limb. Make second cut from above limb. Continue cut until you cut limb off. 3. Make third cut as close to tree trunk...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :