Évaluations - 4, GPA: 4 ( )

Fabricant : Desa Taille : 1.03 mb Nom Fichier : Langue d'enseignement:

Chain must stop moving when you release trigger. Have faulty switch replaced by authorized service center. • while in a hurry • while in tree or on a ladder unless trained to do so 8. Wear snug-fitting clothes when operating chain saw. Do not wear loose clothing or jewelry. They can get caught in moving saw chain. 9. Wear the following safety gear when operating chain saw. • heavy-duty gloves (wear rubber gloves when working outdoors) • steel-toed safety footwear with nonskid soles • eye protection such as safety glasses, goggles, or face screen • safety hard hat • ear mufflers or ear plugs • hair covering to contain long hair • face or dust mask (if working in dusty areas) 10. Before cutting, always provide the following: • clear work area • secure footing • planned retreat path from falling tree 11. Inspect tree before cutting down. Make sure there are no dead limbs or branches that may fall on you. 12. To reduce the risk of electric shock, this saw has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet of your extension cord, reverse the plug. If it still does not fit, a polarized extension cord will be necessary. Do not change the plug in any way. WHILE OPERATING SAW 1. Stay alert. Use common sense while operating chain saw. 2. Keep work area clean. Cluttered areas invite injuries. 3. Be aware of extension cord while operating chain saw. Be careful not to trip over cord. Keep cord away from chain and operator at all times. 4. Keep children, animals, and bystanders away from chain saw and extension cord. Only chain saw user should be in work area. 5. Do not cut down a tree unless you are trained or have expert help. 6. If two or more persons perform bucking and felling operations at the same time, provide plenty of distance between operations. Provide distance of at least twice the height of tree being felled. 7. Secure wood you are cutting by using clamps or chocks. 8. Grip chain saw firmly with both hands. Never operate chain saw with one hand. Never use hand guard as handle. 9. Keep finger off trigger until ready to make cut. 10. Before starting chain saw, make sure chain is not touching anything. 11. To guard against electrical shock, avoid body contact with grounded objects such as pipes, fences, and metal posts. 12. Keep all parts of body away from chain when saw is running. 13. Do not force chain saw while cutting. Apply light pressure. It will do the job better and safer at the rate for which it was intended. 14. Cut small brush and saplings with extreme care. Slender material may catch in chain and be whipped toward you. This could also pull you off balance. 15. When cutting limb or tree trunk that is under tension, use extreme caution. Be alert for wood springing back. When wood tension is released, limb could spring back and strike operator causing severe injury or death. 16. Carry chain saw from one place to another • with saw stopped and unplugged • by holding front handle (never use hand guard as handle) • with finger off trigger • with guide bar and chain to rear WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known (to the state of California) to cause cancer, birth defects, or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints • crystalline silica from bricks and cement and other masonry products • arsenic and chromium from chemically-treated lumber Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles. For more information, visit 2 OWNER’S MANUAL SAFETY WARNINGS KICKBACK WARNING: Kickback may occur when the nose or tip of the guide bar touches an object, or when the wood closes in and pinches the saw chain in the cut. Tip contact in some cases may cause a lightning fast reverse reaction, kicking the guide bar up and back towards the operator. Pinching the saw chain along the top of the guide bar may push the guide bar rapidly back towards the operator. Either of these reactions may cause you to lose control of the saw which could result in serious injury to user. Kickback Safety Devices On This Saw This saw has a low-kickback chain and reduced kickback guide bar. Both items reduce the chance of kickback. Kickback can still occur with this saw. Properly install front hand guard. This item can reduce injuries from kickback. Follow assembly instructions on page 6. Do not remove front hand guard. Do not replace front hand guard with substitute. The following steps will reduce the risk of kickback. • Use both hands to grip saw while saw is running. Use firm grip. Thumbs and fingers must wrap around saw handles. •Keep all...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :