Continual or regular users should therefore monitor closely the condition of their hands or fingers. If any of the symptoms appear, seek immediate medical advice. 3 Never carry the chainsaw with the engine running. Whenever carrying a chainsaw, even for short distances, the chain should be covered by the chain guard (scabbard) and the bar should point backwards. When transporting the chainsaw in a vehicle, secure the saw to prevent fuel spillage. 4 To avoid kick-back, do not attempt to cut with

4 OIL FILTER The oil filter is on the end of the oil suction hose inside the oil tank. To clean and replace the filter pull it out through the oil tank filter opening. Use a piece of bent wire or long forceps. To remove deposits from the oil tank half-fill it with kerosene or petrol and shake thoroughly. Drain off and fill the tank with fresh saw chain oil. Never use waste oil. 5 FUEL FILTER To change fuel filter remove the tank cap and pull out the filter with a piece of bent wire or long force

Oil/petrol mix B. Safety precautions 1 All operators should read this manual carefully before using this chainsaw; only use this machine for usage specifically mentioned in this manual. Wear suitable clothing. This should include snugly-fitting (safety) clothing, sturdy boots, heavy duty gloves, goggles or a face screen and ear plugs or ear mufflers. Wear a helmet if there is risk of falling objects or projections from trees. 2 Always hold the chainsaw firmly with both hands when the engine is r

Before commencing, the chain should be tensioned correctly and the chain brake should be activated to prevent the chain from moving. 2 To obtain a correct sharpening the file must be carefully held to maintain 3 basic angles: – “A” Top angle 30° - 35° – “B” External, side angle 85° - 90° – “C” Internal, side angle 60° File in one direction only, from the “inside” of the cutter tooth towards the “outside”. Do not allow the file to touch the chain as you bring it back to re-position it. Each cutte

If acceleration is not smooth, open another 1/8 turn to increase fuel flow . • H: The needle screw H governs fuel flow at high speed (throttle valve fully open). To set hi speed screw H: close screw H turning it clockwise without forcing . Then open screw 1 full turn (counterclockwise) . If the engine speed is too high, open the screw about 1/8 turn (counterclockwise). Optimal adjustment is found between 1 and 1 1/4 turns. • I: The I (IDLE) screw controls the throttle opening to govern idle spee

Directive 2000/14/ECC (Annex V). Valmadrera, 15.12.01 Pino Todero (Direttore Tecnico) E.O.P.I. ENGLISH - 6 Fault finding table Engine will not start Engine runs badly The chainsaw runs but does not cut well Engine runs badly or looses power when cutting Check STOP switch is in the position I. • Control fuel level min. 25% tank capacity. • • Check air filter is clean. • • Remove spark plug, dry it, clean it and adjust it, and replace it, if necessary. • • Control and adjust the carburetor screws

Refer to “Maintenance” for indications on ensuring that the chain oil is sufficiently distributed. Choice of chain oil Always use new oil only (special type for chains) with adequate viscosity: the oil must adhere well and guarantee good running properties in both winter and summer. If chain oil is not available, EP 90 transmission oil can be used. Never use waste oil because this is this harmful to health, the machine and the environment. Make sure that the oil is suitable for the temperature o

© Electrolux Outdoor Products The Electrolux Group. The world’s No.1 choice. The Electrolux Group is the world’s largest producer of powered appliances for kitchen, cleaning and outdoor use. More than 55 million Electrolux Group products (such as refrigerators, cookers, washing machines, vacuum cleaners, chain saws and lawn mowers) are sold each year to a value of approx. USD 14 billion in more than 150 countries around the world. PN. 249411 REV. 01 (06/04) A. GENERAL DESCRIPTION 1) Rear handle

Preliminary cutting operations and identifying the retreat path. Eliminate any branches that interfere with the job (fig.8), starting from top to bottom, and then, always keeping the trunk between the user and the machine eliminate the more difficult branches afterwards, piece by piece. Eliminate all plants that interfere with work operations and control the area for possible obstacles (rocks, roots, ditches,etc.) when planning the retreat path (to follow during tree fall); Refer to the illustra

The chain must be arrested and the user must wear suitable protective gloves. 4. Clothing. When using this machine the user must wear the following homologated individual protective clothing : close-fitting protective clothing, safety boots with non-slip soles, crush-proof toe puffs and cut- proof protection; cut-proof vibration-proof gloves, protective goggles or safety visor (remove protective film where present); ear protection muffs; helmet (if there is any danger of falling objects); some e