Lubricate the clutch bearing with the same type of grease as used for the guide bar with nose wheel, i. e. ball bearing grease. Use the grease gun supplied with the kit of tools: Remove the clutch housing. Inject grease through the hole in the centre of the clutch. Two strokes of the grease gun will be sufficient. (Check that grease emerges from the gun when it is pumped.) Schmieren des Nadellagers in der Kupplungstrommel Das Kupplungslager mit Fett der gleichen Art wie die Schiene mit Umlenkrol

Make sure that no-one else is in this ”risk zone” before or during felling. ! WARNING! Never attempt to cut logs while they are in a pile or when a couple of logs are lying together. Such procedures drastically increase the risk of kickback which can result in a serious or fatal injury. 1 2 3 IMPORTANT! It takes a lot of experience to fell a tree. Inexperienced users of chain saws should not fell trees. Do not attempt any task that you feel unsure of! WORKING TECHNIQUES Felling direction The aim

• Always file cutting teeth from the inside face. Reduce the pressure on the return stroke. File all the teeth on one side first, then turn the chain saw and file the teeth on the other side. • File all the teeth to the same length. When the length of the cutting teeth is reduced to 0.16 inch (4 mm) the chain is worn out and should be replaced. General advice on adjusting depth gauge setting • When you sharpen the cutting tooth (A) the depth gauge setting (C) will decrease. To maintain optimal c

E EEEEn nnnng ggggl lllli iiiis ssssh hhhh ( ((((2 2222- ----4 44442 2222) )))) Lea detenidamente el manual de instrucciones y asegurese de entender su contenido antes de utilizar la maquina. S SSSSp ppppa aaaan nnnni iiiis ssssh hhhh ( ((((4 44443 3333- ----8 88884 4444) )))) 115 13 81-96 Rev.3 2008-12-16 KEY T O SYMBOLS 2 – English 115 13 81-96 Re v .3 2008-12-16 Symbols on the mac hine: W ARNING! Chain saws can be dangerous! Careless or improper use can result in serious or fatal injury to th

32 Checking, maintaining and servicing chain saw safety equipment .................................................. 33 Muffler ................................................................... 35 Starter ................................................................... 36 Air filter .................................................................. 37 Spark plug ............................................................. 37 Lubricating the bar tip sprocket ............................. 37

See the instructions data. under the headings Fuel Handling and Starting and Stopping. Never use the machine if you are fatigued, while under the influence of alcohol or drugs, medication or anything • Do not use the chain saw until sufficient chain oil has that could affect your vision, alertness, coordination or reached the chain. See instructions under the heading judgement. Lubricating cutting equipment. Wear personal protective equipment. See instructions • Long-term exposure to noise can r

Remove the cut pieces from the cutting area. By leaving them in the cutting area, you increase the risk for inadvertently getting a kickback, as well as increasing the risk of losing your balance while working. The log is lying on the ground. There is little risk of the chain jamming or the object splitting. However there is a risk that the chain will touch the ground when you finish the cut. Cut all the way through the log from above. Avoid letting the chain touch the ground as you finish the c

If a hollow forms on the underside of the bar tip this is due to running with a slack chain. • To prolong the life of the bar you should turn it over daily. ! WARNING! Most chain saw accidents happen when the chain touches the operator. Wear personal protective equipment. See instructions under the heading Personal protective equipment. Do not tackle any job that you feel you are not adequately trained for. See instructions under the headings Personal protective equipment, How to avoid kickback,

First your brake must be in working order. Testing the brake is simple, see instructions under the heading Checking, maintaining and servicing chain saw safety equipment.We recommend you do before you begin each work session. Second the kickback must be strong enough to activate the chain brake. If the chain brake is too sensitive it would activate all the time which would be a nuisance. Will my chain brake always protect me from injury in the event of a kickback? No. First, the chain brake must

If you need further information please contact your nearest servicing dealer. ! WARNING! Never use a machine with defective safety components. Safety equipment must be inspected and maintained. See instructions under the heading Checking, maintaining and servicing chain saw safety equipment. If your machine does not pass all the checks, take the saw to a servicing dealer for repair. Chain brake and front hand guard Your chain saw is equipped with a chain brake that is designed to stop the chain