Évaluations - 3, GPA: 4.3
(
)
)
|
Facilité d'utilisation
Age: 1. years - 5 years. Weight Limit: 50 lbs. (23 kg). Tools needed for assembly: Phillips Screwdriver, Hammer and Scrap Block of Wood (all not included). Consumer Information Fasteners WARNING To avoid serious injury: • Adult supervision is required. • Never use near cars and other motor vehicles, near streets, steps, sloped driveways, hills, roadways, alleys, swimming pool areas or other bodies of water. • Always wear shoes or sneakers. • Never allow more than one (1) rider. All SHOWN ACTUAL SIZE #8 x 3" Screw – 1 Cap Nut – 1* #10 x 3/4" Screw - 11 #8 x 3/4" Screw - 13 *Note: For your convenience, an extra cap nut is included. Note: Tighten and loosen the screws with a Phillips screwdriver. Do not over-tighten the screws. 2 3 Parts Seat Pin Seat Handlebar Handle Pin Frame Cover Handle Top Handle Bottom Base 2 Base/Handle Covers Fork Front Wheel Assembly 2 Fork Covers 4 Pedal Axle Covers Straight Axle 2 Rear Wheels Cap Nuts 2 Wheel Caps Frame Footrest Note: The base/handle assembly can be attached to the trike in either the Ride-on Rocker (page 9) or Learn to Pedal (page 10) mode. Parts not shown: Assembly Tool and Label. Assembly This product contains small parts in its unassembled state. Adult assembly is required. CAUTION • Please save all packaging material until assembly is complete to ensure that no parts are discarded. • Please wipe each part with a clean, dry, cloth before assembling this product. 1 Straight Axle Rear Wheel Spoke Side Down • Slide a rear wheel (spoke side down) onto the straight axle. • Turn the frame upside down. • Insert the straight axle assembly through the holes in the rear of the frame. • Fit the wheel cap into the center of the wheel. Tap the wheel cap with a hammer to secure it to the wheel. Frame Wheel Cap HoleHole Rear Wheel Straight Axle Bottom View 2 4 Assembly 3 Cap Nut Straight Axle Rear Wheel Spoke Side Up Assembled Rear Wheel Assembly Tool Scrap Block of Wood • Turn the frame on its side with the exposed end of the straight axle up. • Place the assembled rear wheel on the scrap block of wood. • Slide the other rear wheel (spoke side up) onto the end of the straight axle. • Place a cap nut on the end of the straight axle. • Place the assembly tool over the cap nut and tap it with a hammer. Gently pull the rear wheel up to be sure the cap nut is securely attached to the straight axle. • Fit the wheel cap into the center of the wheel. Tap the wheel cap with a hammer to secure it to the wheel. • Set the frame assembly aside. 4 Wheel Cap 5 Pedal Axle Cover Pedal Axle CoverMetal Tab Slot Pedal Axle • Fit two pedal axle covers onto the pedal axle metal tabs. Make sure the metal tabs fit into the slot in each pedal axle cover. • While holding the pedal axle covers on the pedal axle, insert the pedal axle into the hole in the center of the front wheel. • Push the pedal axle covers into the center of the front wheel until they are flush with the surface of the front wheel. • Repeat this procedure with the other two pedal axle covers on the other side of the front wheel assembly. 5 Assembly 6 Fork Cover Fork Arms GroovePedal Axle Front Wheel Assembly • Place the front wheel assembly between the fork arms so that the pedal axle fits into the groove at the bottom of each fork arm. • Place a fork cover over the pedal axle on one fork arm. • Insert two #10 x ." screws into the fork cover and tighten. • Repeat this procedure to attach the other fork cover to the other fork arm, using the #10 x ." screws. • Turn the frame upright. • Insert the fork post up through 7 Handlebar Frame Neck Fork Covers Fork Post FIRST, insert the screw so that ." is visible. THEN, tighten the screw. ." the hole in the frame neck. Make sure the fork is positioned so that the fork covers face the rear wheels. • Place the handlebar over the fork post and push it down onto the frame. Make sure the handlebar is positioned so that the screw hole faces the rear wheels and aligns with the screw hole in the fork post. • Insert the #8 x 3" screw through the hole in the handlebar and into the fork post so that part of the screw (about .") is still visible. Tighten the screw. Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052, U.S.A. ©2008 Mattel, Inc. All Rights Reserved. ® and TM designate U.S. trademarks of Mattel, Inc. PRINTED IN MEXICO 73528c-0920 6 Assembly • Insert the knobbed end of the foot- rest up through the opening in the underside, center of the frame . • Rotate the footrest . turn . • Slide the footrest toward the 8 Frame Opening Footrest Knobbed EndFootrest Top View Knobbed End 2. 3 .121 10 Seat Mount Adjustment Holes Seat Seat Mount handlebar as far as it will go until the top of the footrest is positioned over the opening’s rectangular cut-out. • Lower the knobbed end of the footrest into the rectangular cut-out in the frame 3 . • Place the seat on the seat mount. • Adjust the seat for your child’s comfort by aligning the hole in the seat with one of the ...