Log:
Téléchargements : 0   Taille : 5 mb   Fabricant : Huffy  
Catégorie : Jouets
@name

WARNING! IF YOUR SYSTEM IS EQUIPPED WITH AN ACRYLIC BACKBOARD, EXAMINE BACKBOARD FOR ANY DAMAGE THAT MAY HAVE OCCURRED DURING SHIPMENT. CRACKS IN THE BACKBOARD COULD RESULT IN SUDDEN BREAKAGE. IF BACKBOARD IS DAMAGED IN ANY WAY PRIOR TO OR AFTER ASSEMBLY, CALL TOLL-FREE NUMBER: U.S. 1-800-558-5234; CANADA: 1-800-284-8339; ID# M6809011 12/06 4 Get to know the basic parts of your basketball system... TOP POLE MIDDLE POLE BOTTOM POLE STRUTS ELEVATOR ASSEMBLY BACKBOARD BASE WHEEL CARRIAGE ASSEMBLY F

Téléchargements : 6   Taille : 3 mb   Fabricant : Huffy  
Catégorie : Jouets
@name@name@name@name

4. 54 11 11 60 59 55 54 58 23 23 Assemble lanyard (26) to locking pin (27) as shown (FIG A). Attach covers (35) onto pole mount bracket (28) with carriage bolt (19) and nut (11) as shown. IMPORTANT! Loop end of pin lanyard (26) over carriage bolt (19) as it passes through the pole mount bracket (28) during this assembly. IMPORTANT! Indicator labels should be applied as close to holes as possible to prevent labels from being damaged during height adjustment. ID# M6011141 04/06 18 29 30 30 29 52 I

Téléchargements : 13   Taille : 2 mb   Fabricant : Huffy  
Catégorie : Jouets
@name

Mark pole sections with tape (not supplied) at indicated distances from ends as shown. Tape (Not Supplied) 18" (42.7 cm) 6" (15.2 cm) 24" (61 cm) PLAYING SURFACE GROUND SURFACE 2. Ensure ground is level with playing surface, then dig pole hole. CONTACT UTILITIES BEFORE DIGGING. WARNING! IMPORTANT!: Maximum distance from edge of hole to edge of playing surface 6” (15.2 cm). 9 10/04 P/N 21168202 4. 1" (2.54 cm) SIDE VIEW Fill hole approximately 1/3 full with mixed concrete. FIG. A FLANGE Insert gr

Téléchargements : 0   Taille : 2 mb   Fabricant : Huffy  
Catégorie : Jouets
@name@name@name

22 51 51 49 21 41 ID# M731324 11/05 28 29 11/05 ID# M731324 13 23 27 52 10. Insert lower adjustment rod (52) into bottom of adjustment tube (49), pull trigger to allow lower adjustment rod to move about mid-way into adjustment tube (49), release the trigger so the lower adjustment rod (52) locks into position midway inside the adjustment tube (49). Attach the lower adjustment rod (52) to elevator bracket (27) using bolt (23) and nut (13) as shown. Enfilez la tige d'ajustement inferieure (52) dan

Téléchargements : 11   Taille : 2 mb   Fabricant : Huffy  
Catégorie : Jouets
@name

1 35 29 29 33 33 33 33 35 30 30 Support pole on sawhorse. Attach backboard assembly to top pole section (1). NOTE: Two people are required for this step, use caution, elevator assembly is heavy. 31 31 TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT IN SERIOUS BODILY INJURY AND/OR PROPERTY DAMAGE. WARNING 1 35 29 29 33 33 33 33 35 30 30 Support pole on sawhorse. Attach backboard assembly to top pole section (1). NOTE: Two people are required for this step,

Téléchargements : 25   Taille : 2 mb   Fabricant : Huffy  
Catégorie : Jouets
@name@name

FRONT TOP POLE BACK MIDDLE POLE RIM BOTTOM POLE STRUTS ELEVATOR ASSEMBLY BACKBOARD BASE 1. Correctly identify each pole section. Poles have an identification sticker that will be used as a reference point in the next step. 3 2 4 Reference Stickers TOP MIDDLE BOTTOM Toll-Free Customer Service Number for U.S. : 1-800-558-5234 7 12/04 P/N 21473501 IMPORTANT! ONCE POLE SECTIONS ARE POUNDED TOGETHER- THEY CANNOT BE TAKEN APART 2. 3 2 4 TOP MIDDLE BOTTOM alignment mark alignment mark Align poles using

Téléchargements : 7   Taille : 1 mb   Fabricant : Huffy  
Catégorie : Jouets
@name

WRITE IN YOUR MODEL NUMBER: ___________ IMPORTANT! In U.S. and Canada only: Have questions?...don’t go back to the store! We appreciate your purchasing one of our many fine products. We are sure that you will be very satisfied with your selection. Although great care and effort have been taken, occasionally problems may occur. To ensure prompt and correct handling of any problems, or to answer any questions, please contact our Toll-Free Customer Service Number listed below. Service will be quick

Téléchargements : 0   Taille : 1 mb   Fabricant : Huffy  
Catégorie : Jouets
@name

SAFETY INSTRUCTIONS FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY, PROPERTY DAMAGE AND WILL VOID WARRANTY. This unit is intended for display purposes only and should not be used for play. To ensure safety, do not attempt to assemble this system without following the instructions carefully. Check entire box and inside all packing material for parts. Before beginning assembly, read the instructions and identify parts in this document. Proper and complete assembly, use an

Téléchargements : 3   Taille : 1 mb   Fabricant : Huffy  
Catégorie : Jouets
@name

35 19. 20. Install spacers (51) onto backboard brackets (52), with bolts (53, 54) and lock nuts (55, 37) as shown. 53 51 37 52 55 54 IMPORTANT!: KEEP HARDWARE LOOSE UNTIL AFTER STEP 25 IS COMPLETED. P/N 211574 09/04 18 58 59 57 56 56 59 68 58 59 57 56 56 59 68 56Lower Elevator tube Toward Pole 52 21. Toward Board Identify elevator tubes (63 & 56). Toward 63 Toward Board Pole Upper Elevator tube Attach lower elevator tubes (56) and counter balance spring (68) to backboard support brackets (52) us

Téléchargements : 6   Taille : 1 mb   Fabricant : Huffy  
Catégorie : Jouets
@name

x 4-3/4 Long 8 1 202822 Eyebolt, 3/8-16 x 2-1/2 Long 9 6 203063 Lock Nut, 3/8-16 10 2 906206 Tank Strut 11 1 201625 Bolt,Yellow Dichromate, 5/16-18 X 3.60 Long 12 6 203218 Washer, Flat, 5/16 13 1 203099 Lock Nut, 5/16-18 14 4 204961 Bolt, Hex Head, 3/8-16 x 0.625 Long 15 6 205528 Bolt, Hex Flange, 5/16-18 x 1 Long 16 6* 203100 Nut, Hex Flange, 5/16-18 17 4 201651 Spacer .500 I.D. x .25 Long 18 2 206303 Washer 1/4 Flat 19 1 200627 Wheel Bracket 20 2 204558 Screw, Phillips, 1/4 x .375 Long, Type 2





catégories