Évaluations - 6, GPA: 3.8
(
)
)
|
Par ce dispositif a également d'autres instructions :
Facilité d'utilisation
5 Set the alarm time. 1 Press – . or >+ to select the hour digits and press NxPLAY/STOP. The minute digits will flash. 2 Press – . or >+ to select the minute digits and press NxPLAY/STOP. “ALARM ON” and “,” will be displayed to indicate that the setting has been completed. 6 Press MENU to exit the menu mode. “,” is displayed when the number of the message with alarm setting is selected. At the set time, the alarm will sound for about 10 seconds and the selected message will be played back. During playback, “ALARM” will flash in the display window. When the playback ends, the unit will stop automatically at the beginning of that message. To listen to the same message again Press NxPLAY/STOP. The same message will be played back from the beginning. To cancel the alarm setting before the playback starts Press STOP while the alarm sound is heard. You can stop even when the HOLD function is activated. Notes • You cannot set the alarm if you have not set the clock or there is no message in the selected folder (the unit will not enter the alarm setting mode when you press MENU in Step 2). • If you try to set the alarm to play back a message at a previously set time on another message, “PRE SET” will be displayed, preventing new settings. • If the alarm time comes while another message is being played back with an alarm, the playback stops and the new message will be played back. • If the alarm time comes during recording, alarm will sound for 10 seconds after the recording is finished and playback begins. “,” will flash when the alarm time comes. • If more than one alarm time comes during recording, only the first message will be played back. • When the alarm time comes when the unit is in the menu mode, alarm will sound and the menu mode will be cancelled. • If you erase the message you set the alarm to play back, the alarm setting will be cancelled. • If you add an index to the message you set the alarm to play back, playback will stop at the index. • If you erase the index on the message you set the alarm to play back, the alarm setting will be cancelled. • You can adjust the playback volume with the VOL control. • If the alarm time comes during erasing, alarm will sound for 10 seconds after the erasing is finished and playback begins. • Alarm setting will not be cancelled when the alarm playback finishes. To cancel alarm setting, see below. To cancel the alarm setting or change the alarm time 1 Select the message you set the alarm to play back, and press MENU. “ALARM ON” will be displayed. 2 Press NxPLAY/STOP to flash “ON”. 3 To cancel the alarm setting: Press – . or >+ to flash “OFF” and press NxPLAY/STOP. To change the alarm date and time: Press NxPLAY/STOP. When the alarm date is displayed, follow the steps 3 to 5 above to change the alarm date and time. 4 Press MENU to exit the menu mode. Preventing Accidental Operation — HOLD function Slide the HOLD switch in the direction of the arrow. “HOLD” will flash three times, indicating that all the functions of the buttons are locked. To cancel the HOLD function, simply slide the HOLD switch in the opposite direction. Note When the HOLD function is activated during recording, cancel the HOLD function first to stop recording. 1 Tip Even if the HOLD function is activated, you can stop the alarm playback. To stop the alarm or playback, press STOP. Selecting the Display Mode You can select the display mode for the stop, recording and playback modes. (If the unit is left unoperated for more than 3 seconds in the stop mode, the display will show the current time, regardless of the display mode setting.) Each time you press DISPLAY, the display mode will change as shown below: Counter: Elapsed playback/recording time in one message m Remaining recording time: m Recorded date*: The date and time the current message was recorded. * If the clock has not been set, “-M--D ---:--” will be displayed. Turning off the Beep Sound BEEP ON: A beep will sound to indicate that operation has been accepted. BEEP OFF: No beep sound will be heard except for the alarm and timer. 1 Press MENU to enter the menu mode. 2 Press – . or >+ to display “BEEP ON (or OFF)” and press NxPLAY/STOP. “ON (or OFF)” will flash. 3 Press – . or >+ to select “ON” or “OFF” and press NxPLAY/STOP. The setting is completed. 4 Press MENU to exit the menu mode. What beep sound means Beep patterns Meaning - (single tone) Usual mode -- (double tone) Enter/exit special mode --- (triple tone) Notice* ---- (forth tone) Lack of battery power. ---- ---- (continuous beep) Alarm set time has come. * This pattern lets you know the procedure is wrong or informs you of some messages, such as: - you are trying to record a message when you have already recorded up to the maximum recordable time or the maximum number of messages. - you reaches at the top of the first message or end of the last message in a folder. , Index to Parts and Controls Main unit MIC jack (PLUG IN POWER) EAR (earphone) jack OPR (operation) indicator zREC (...