Évaluations - 3, GPA: 4
(
)
)
|
Facilité d'utilisation
GENERAL PRODUCT CARE To keep your answerer working and looking good, follow these guidelines: • Avoid putting it near heating appliances and devices that generate electrical noise (for example, motors or fluorescent lamps). • DO NOT expose to direct sunlight or moisture. • Avoid dropping and other rough treatment to the answerer. • Clean with a soft cloth. • Never use a strong cleaning agent or abrasive powder because this will damage the finish. • Retain the original packaging in case you need to ship it at a later date. CLEANING THE TAPE MECHANISM These parts should be cleaned periodically in the following manner: 1. Remove the cassette from the answerer. 2. Clean the head surfaces, pressure rollers and capstans with a cotton swab. If these surfaces are extremely dirty, dampen the cotton swab HEAD PRESSURE ROLLER CAPSTAN with alcohol. WARNING:TO PREVENT FIRE OR ELECTRICAL SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. THE LIGHTNING FLASH AND ARROW- HEAD WITHIN THE TRIANGLE IS A WARNING SIGN ALERTING YOU OF "DANGEROUS VOLTAGE" INSIDE THE PRODUCT. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USERSERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. THE EXCLAMATION POINT WITHIN THE TRIANGLE IS A WARNING SIGN ALERTING YOU OF IMPORT ANT INSTRUCTIONS ACCOMPANYING THE PRODUCT. SEE MARKING ON BOTTOM / BACK OF PRODUCT FCC NUMBER IS LOCATED ON THE CABINET BOTTOM REN NUMBER IS LOCATED ON THE CABINET BOTTOM Models 2-9801 347A8232-0001 (Rev. 0, E/S) P.O. Box 1976, Indianapolis, IN 46206 © 1996 Thomson Consumer Electronics, Inc. Printed in China Trademark(s) ® Registered Marca(s) Registrada(s) INSTALLATION Use the steps below to connect your new answerer for proper operation. Make sure you have a modular telephone jack and a standard AC electrical outlet near the place you have chosen to install your answerer. 2 STOPPLAY A MC-30 MICROCASSETTE TM 0 5 10 4 5 1 FROMTELEPHONE 3 1. Remove door by lifting it from the back edge. 2. Insert the cassette tape with side ”A” facing up. 3. Connect your telephone’s line cord into the jack marked FROM TELEPHONE on the back of the unit. (You don’t have to connect your telephone for the answerer to record incoming messages.) 4. Plug the answerer’s telephone line cord into a modular wall jack. 5. Plug the power supply cord into an AC power outlet. SETUP RECORDING THE OUTGOING ANNOUNCEMENT Before using your new answerer you should record an outgoing announcement. This is the announcement that the callers will hear when the system answers a call. When recording the announcement you should be about six inches from the unit, and should eliminate as much background noise as possible. 1. Prepare your announcement. Sample Announcement: Hi, this is (use your ANNOUNCEMENT button name here), I can't answer the phone right now, so please leave your name, number and a brief message after the tone, and I'll get back to you. Thanks. 2. Hold down the ANNOUNCEMENT button. Begin recording after the tone. 3. Release the ANNOUNCEMENT button when you finish the announcement. To review the outgoing announcement, press and release the ANNOUNCEMENT button. MESSAGES INDICATOR MESSAGES Indicator is on — Answerer is on and there are no messages. MESSAGES Indicator is Flashing — Number of flashes indicates number of messages. You need to reset the tape by playing messages to stop the flashing. MESSAGES Indicator is OFF — Answerer is off, but you might still have messages. MESSAGES indicator MIC VOL OFF ANNOUNCEMESSAGES STOPPLAY MESSAGES Indicator is flashing rapidly — Indicates no valid outgoing announcement, or that the tape is full. Re-record your outging announcement. ANSWERER OPERATION VOLUME/ON OFF CONTROL • Use the volume control to adjust the volume to LO or HI. • Use the volume control to turn the answer on or off, when the volume is in the OFF position the answerer is off. MESSAGE PLAYBACK Your answerer has been programmed to automatically answer on the second ring if you have messages and the fifth ring if you don't have messages. If your answerer has recorded incoming messages, the MESSAGES indicator will flash once for each message received followed by a brief pause. • Press and release the PLAY/STOP button to play messages (use VOLUME control to adjust speaker volume). The answerer plays all messages, automatically resets, and is ready to record new messages over the old messages on the tape. To begin recording new messages over old messages at the beginning of the tape, see "Clearing New Messages from the Tape" below. To stop playback: • Press the PLAY/STOP button again. To repeat playback: • Press the PLAY/STOP button again after the answerer is idle. TAPE FULL When the tape is full, the MESSAGES indicator flashes rapidly and the unit answers on the tenth ring. Enter the security code (located on the bottom of the unit) and messages play automatically. Enter the security code again to l...