Évaluations - 2, GPA: 5 ( )

Fabricant : Milwaukee Taille : 416.12 kb Nom Fichier : Langue d'enseignement:

Use only specifically recommended accessories. Others may be hazardous. Removing and Replacing Quik-Lok® Cords (Fig. 1) Cat. No. 9072-20, 9072-22, 9092-20 and 9096-20 MILWAUKEE's exclusive Quik-Lok® Cords provide instant fi eld replacement or substitution. Fig. 3 Drive shank Fig. 1 1. To remove the Quik-Lok® Cord, turn the cord nut 1/4 turn to the left and pull it out. 2. To replace the Quik-Lok® Cord, align the connector keyways and push the connector in as far as it will go. Turn the cord nut 1/4 turn to the right to lock. Attaching and Removing the Tool Hanger (Fig. 2) Cat. No. 9092-20, 9096-20, or as an accessory Fig. 2 Gear case screws Tool hanger Ring 1. To attach, remove the two top gear case screws (Fig. 2). 2. Place the ring through the tool hanger. 3. Position the tool hanger on the tool over the two gear case screw holes. 4. Replace the two gear case screws. Hand tighten the screws. 5. To remove, reverse the procedure. 1. To attach a socket or other accessory, push the accessory onto the drive shank until it snaps into place. 2. To remove the accessory, pull it off the drive shank. Attaching and Removing Accessories (Fig. 4) Cat. No. 9070-20, 907220, 9072-22 These impact wrenches are intended only for use with sockets designed for impact wrenches and that have a 1/2" square drive. Other sockets could shatter or break, causing injury. Fig. 4 Drive shank Detent pin 1. To attach a socket or other accessory, align the hole in the accessory with the detent pin on the drive shank. Hold the detent pin in while pushing the socket onto the drive shank. The detent pin will snap into place in the hole to secure the socket. 2. To remove the accessory, insert a nail or other thin object into the hole in the accessory and press the detent pin in. Pull the accessory off the drive shank. Attaching and Removing Accessories (Fig. 5) Cat. No. 9092-20, 9096-20, or other Impact Wrenches using the Quick Change 1/2" Square Drive to 7/16" Hex Adapter Cat. No. 9092-20 and accessory Cat. No. 48-66-0061 are intended for use with drill bits and adapters with a 7/16" Hex Quick Change shank. Cat. No. 9096-20 is intended for use with drill bits and adapters with a 5/8" Hex Quick Change shank. Both Hex Quick Change shanks have a ball-retainer groove. They are not intended for use with Hex Shank Bit Extensions. WARNING Use only sockets and other accessories specifically designed for use on impact wrenches and drivers. Other sockets and accessories might shatter or break causing injury. Attaching and Removing Accessories (Fig. 3) Cat. No. 9071-20, 9075-20 This impact wrench is intended only for use with sockets designed for impact wrenches and that have a 1/2" square drive (3/4" square drive for Cat. No. 9075-20). Other sockets could shatter or break, causing injury. Fig. 5 Open (Release) Closed (Locked) Ball-retainer groove 1. To attach an accessory, pull the chuck collar forward and insert the accessory shank. Release the collar. It may be necessary to pull the bit out slightly to engage the holding mechanism. 2. To remove the accessory, pull the chuck collar forward and remove the accessory. Release the collar. page 5 OPERATION WARNING To reduce the risk of injury, wear safety goggles or glasses with side shields. Unplug the tool before changing accessories or making adjustments. Using the Forward/Reverse Switch (Fig. 6) Cat. No. 9072-20, 9072-22, 9092-20, and 9096-20 This impact wrench is equipped with a forward/reverse switch that may be set to forward or reverse rotation. Fig. 6 Forward Reverse Forward/ Reverse Switch 1. For forward (clockwise) rotation, push the...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :