Log:
Téléchargements : 0   Taille : 1 mb   Fabricant : Milwaukee  
Catégorie : Perceuses et shuropopverty
@name@name@name

Always replace a damaged extension cord or have it repaired by a qualified person before using it. • Protect your extension cords from sharp objects, excessive heat and damp or wet areas. Recommended Minimum Wire Gauge for Extension Cords* Nameplate Amperes Extension Cord Length 25' 50' 75' 100' 150' 200' 0 - 5 16 16 16 14 12 12 5.1 - 8 16 16 14 12 10 -8.1 - 12 14 14 12 10 -- 12.1 - 15 12 12 10 10 -- 15.1 - 20 10 10 10 -- - * Based on limiting the line voltage drop to five volts at 150% of the r

Téléchargements : 0   Taille : 63 kb   Fabricant : Milwaukee  
Catégorie : Perceuses et shuropopverty

Téléchargements : 0   Taille : 50 kb   Fabricant : Milwaukee  
Catégorie : Perceuses et shuropopverty

Téléchargements : 4   Taille : 102 kb   Fabricant : Milwaukee  
Catégorie : Perceuses et shuropopverty

Téléchargements : 2   Taille : 1 mb   Fabricant : Milwaukee  
Catégorie : Perceuses et shuropopverty
@name

Step 2 Install the leveling screws (8), screwing four (4) into each base. Step 3 Install the feed handles (1) and knobs (2) by screwing one knob onto the end of the handle, then slip thru hub and attach other knob. Step 4 Remove the Manta from the vacuum base by removing the nut and bolt that holds the main assembly to the vacuum base. Set the Manta aside, observing the following precaution. Turn the vacuum base over. Press the gasket into the groove in the underside of the base. The gasket is c

Téléchargements : 0   Taille : 79 kb   Fabricant : Milwaukee  
Catégorie : Perceuses et shuropopverty

Téléchargements : 5   Taille : 303 kb   Fabricant : Milwaukee  
Catégorie : Perceuses et shuropopverty
@name@name@name

Do not use or charge batteries in hot or cold places (below 40°F (5°C) or above 105°F (40°C)). Temperature extremes reduce the ability for battery pack cells to hold a charge. Do not store batteries where the temperature may exceed 120°F (50°C), such as in a vehicle or metal building during the summer. To avoid overheating to a battery pack, allow cordless tools cool down between high torque drilling/cutting applications. The increased energy discharge rate will heat the battery pack cells faste

Téléchargements : 0   Taille : 84 kb   Fabricant : Milwaukee  
Catégorie : Perceuses et shuropopverty

Téléchargements : 0   Taille : 3 mb   Fabricant : Milwaukee  
Catégorie : Perceuses et shuropopverty
@name@name@name

2). 2. Place the ring through the tool hanger. 3. Position the tool hanger on the tool over the two gear case screw holes. 4. Replace the two gear case screws. Hand tighten the screws. 5. To remove, reverse the procedure. WARNING! Use only sockets and other accessories specifically designed for use on impact wrenches and drivers. Other sockets and accessories might shatter or break causing injury. Fig. 3 Drive shank 1. To attach a socket or other accessory, push the accessory onto the drive shan

Téléchargements : 2   Taille : 666 kb   Fabricant : Milwaukee  
Catégorie : Perceuses et shuropopverty





catégories