Log:
Évaluations - 1, GPA: 3 ( )

Instructions Frigidaire, Modèle F36WC

Fabricant : Frigidaire
Taille : 183.65 kb
Nom Fichier :
Langue d'enseignement: en
Aller à la télécharger



Facilité d'utilisation


IT IS A GOOD PRACTICE TO TAPE ALL DUCT CONNEC- TIONS, MAKING THEM BOTH SECURE AND AIR TIGHT. 15.Follow appropriate directions below for type of duct work you are installing: WALL CAPS (FIG. 9) Use a saber saw to cut a hole slightly larger than duct so duct will line up easily with hood. Install casing strips on outside walls finished in siding. Assemble the duct work and tape all joints. Run duct work back to hood. Fasten wall cap to last section of duct and nail or screw cap to wall. Seal all around flange on wall cap with caulking compound. Make sure that enough duct runs into the room so that the duct will overlap the damper/duct connector by 3/4" when the hood is installed. ROOF CAPS Cut hole in roof slightly larger than duct so duct will line up easily with hood. Trim shingles around hole so that they will fit snugly around hood of cap when cap is installed. Assemble the duct work and tape all joints. Run the duct work down to hood. Trim duct parallel to roof pitch, leaving 3/4" of duct projecting above roof. Seal all around duct with roof cement. Install roof cap, inserting back edge of cap under shingles. Seal around cap with roof cement and seal all nail heads and shingles which were cut or lifted. Make sure that enough duct runs into the room so that the duct will overlap the damper/duct connector by 3/4" when the hood is put into place. HORIZONTAL DUCTING AND WIRING (Through Wall) CABINET FRONT / FRENTE DEL GABINETE CABINET BOTTOM 7." 2" 5" WOOD SHIMS ELECTRICAL ACCESS HOLE (in cabinet bottom) 8" DIA. ACCESS HOLE 7” ROUND DUCT VERTICAL DUCTING AND WIRING (Through Cabinet Bottom) CABINET BOTTOM BACK WALL 3-1/4” x 10” DUCT 3/8" 3-7/8" 3/4" 7-1/2" 5-1/4"5-1/4" 1/8" 1-1/2"1-1/2" 9" 7-1/2" 9-7/8" 6-7/8" 10-5/8" 5-1/4" 5-1/4" ROOF CAP 4 INSTALLING THE RANGE HOOD 16.Bring electrical cable through access hole drilled in wall or bottom of cabinet. Provide 6" wire leads and install proper connector for type of cable being used. Remove lock nut from connector and let prepared cable project through cabinet or wall opening so it is ready for installation into range hood. (FIG. 10) 17.Position hood in place so that: a) Electrical line is routed through appropriate knockout opening. This step will have to be accomplished while positioning hood. (FIG. 13) b) Large part of keyhole mounting slots on hood fit onto hood mounting screws projecting from bottom of cabinet. (FIG. 11) c) Damper/duct connector slides into duct work in wall or cabinet. 18. Adjust hood so the front of hood is flush with cabinet front. 19.Tighten the four hood mounting screws securely. 20.Install locknut on electrical connector and tighten securely. 21.Make electrical connection using wire nuts to connect white wire to white, black wire to black. Ground hood to prepared hole using green ground screw provided. (FIG. 12) 22.Replace wiring box cover and screw. Make sure that all wir ing is safely contained inside. NOTE For Ductfree Installations Only: Install both filters. Make sure that ductfree filter (purchase separately) is next to fan assembly with blue side next to blade. Aluminum filter should be facing out. USE AND CARE SWITCHES Right knob controls light. Left knob controls blower. Rotate knob CLOCKWISE to turn blower ON to HIGH speed. Further CLOCKWISE rotation decreases blower speed. Rotate knob fully COUNTERCLOCKWISE (past HIGH speed) to turn fan OFF. CLEANING Finish Keep your range hood clean using a mild detergent suitable for painted surfaces. Aluminum Filters should be cleaned frequently with a deter gent solution to avoid grease build up. They are also dishwasher safe. FILTER REMOVAL Filters are removed by turning filter clip to the side and lifting filter or filters out. In ducted version, turn filter retaining clip to one side and place aluminum filter under embossed retaining tabs on back of fan housing. Turn filter clip so that the low end of clip holds single filter firmly in place. (FIG. 13) In ductfree version, place both aluminum and ductfree filter under tabs on back of fan housing. Turn filter retaining clip so that high end holds both filters firmly in place. Make sure ductfree filter is next to fan assembly, with blue side next to fan blade, and aluminum filter is facing out. NOTE: Make sure that arrows on filter retaining clip point toward back and front of hood. LIGHT BULB REPLACEMENT Light bulb (not supplied with hood) should be 75 watts maximum. The lens covering bulb is removed by pressing the two extending tabs together until they release from the retaining slots. (FIG. 14) FAN ASSEMBLY REMOVAL Be sure power is disconnected. Remove filters. Remove the two screws holding the motor bracket to the range hood and unplug the fan assembly. Be careful not to allow fan assembly to drop when the screws are removed. (FIG. 15). FIG. 10 CONNECTOR FIG. 11 ELECTRICAL LINE FIG. 12 BLACK WIRES GREEN GROUND SCREW GROUND WIRE (BARE OR GREEN WIRE) WHITE WIRES STAR LOCKNUT GROUNDING BRACKET FIG. 13 NON-DUCTED FILTER (SOLD SEPARATEL...

Ce manuel est également adapté pour les modèles :
Lecteur DVD - F30WC (183.65 kb)

Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories