Évaluations - 2, GPA: 4.5
(
)
)
|
Par ce dispositif a également d'autres instructions :
Facilité d'utilisation
• REAR —NONE: If you will not connect a rear speaker, select this. —LARGE (REAR*/SIDE*): Normally select this. —SMALL (REAR*/SIDE*): When the sound cracks or the effects of the surround is difficult to hear, select this. This activates the Dolby Digital bass redirection circuitry and outputs the bass frequencies of the speaker from some other speakers . • SUBWOOFER —NONE: If you do not connect a subwoofer, select this. This activates the Dolby Digital bass redirection circuitry and outputs the LFE signals from the front speakers. —YES: If you connect a subwoofer, select this to output the LFE (low frequency effects) channel from the subwoofer. * Rear speaker position (REAR/SIDE) These items let you specify the location of your rear speakers for proper implementation of “VIRTUAL REAR SHIFT” and “VIRTUAL MULTI REAR” in the Control Menu display. Refer to the illustration below. • Set to “SIDE” if the location of your rear speakers corresponds to section A. • Set to “REAR” if the location of your rear speakers correcponds to section B. This setting effects only the “VIRTUAL REAR SHIFT” and “VIRTUAL MULTI REAR” mode. 90° 20° A B 45° B A Notes • When you select an item, the sound cuts off for a moment. • The cut off frequency for the subwoofer is fixed at 100Hz. • Set the subwoofer‘s cut off frequency as high as possible. • Depending on the settings of other speakers, the subwoofer may output excessive sound. • If your speakers are too small to reproduce low bass frequencies, please set all speaker settings to “SMALL” and utilize a subwoofer for low frequency sound. pDISTANCE You can vary the distance of each speaker as follows. Default adjustments are in the parentheses. • FRONT (3.6m) Front speaker distance can be set in 0.2 meter steps from 1 to 15 meters. • CENTER (3.6m) Center speaker distance can be set in 0.2 meter steps from a distance 0.6 meter farther to the front speaker to a distance 1.6 meters closer to your listening position. • REAR (3.0m) Rear speaker distance can be set in 0.2 meter steps from a distance equal to the front speaker distance to a distance 5 meters closer to your listening position. Notes • When you set the distance, the sound cuts off for a moment. • If each of the front or rear speakers are not placed an equal distance from your listening position, set the distance of the closest speaker. • Do not place the rear speaker farther away from your listening position than the front speakers. Settings 61 Speaker Set Up Settings and Adjustments pBALANCE You can vary the balance of each speaker as follows. Default adjustments are in the parentheses. • FRONT (0dB) Adjust the balance between the front left and right speakers (-6dB [L] to +6dB [R], 0.5dB steps). • REAR (0dB) Adjust the balance between the rear left and right speakers (-6dB [L] to +6dB [R], 0.5dB steps). pLEVEL You can vary the level of each speaker as follows. Default adjustments are in the parentheses. • CENTER (0dB) Adjust the level of the center speaker (-6dB to +6dB, 0.5dB steps). • REAR (0dB) Adjust the level of the rear speakers (-6dB to +6dB, 0.5dB steps). • SUBWOOFER (0dB) Adjust the level of the subwoofer (-10dB to +6dB, 0.5dB steps). pTEST TONE You can hear the test tone from each speaker in sequence. • OFF: The test tone is not emitted from speakers. • ON: During adjustment of “BALANCE” or “LEVEL,” the test tone is emitted from both speakers simultaneously. Note While you are playing a disc, you cannot hear the test tone. Execute the test tone after you stop playback. To adjust the volume of all the speakers at one time Use the receiver’s (amplifier’s) volume control. To return to the default setting Select the item, then press CLEAR. Adjusting the speaker volume 1 While you stop playback, select “SPEAKER SETUP” after pressing SET UP. 2 Select “TEST TONE” and set “TEST TONE” to “ON.” You will hear the test tone from each speaker in sequence. 3 From your listening position, select “BALANCE” or “LEVEL” and adjust the value of “BALANCE” and “LEVEL” using >/.. During this adjustment, the test tone is emitted from both speakers simultaneously. 4 Select “TEST TONE” and set “TEST TONE” to “OFF” to turn off the test tone. 62 Controlling the TV or the AV Receiver (Amplifier) with the Supplied Remote Z If you adjust the remote signal, you can control your TV with the supplied remote. Default setting is to control Sony TVs with the gmark. When you connect the player to a Sony AV receiver (amplifier), you can also set the input of the receiver (amplifier) to this player with the supplied remote. TV/DVD 1 2 3 4 5 6 7 8 9 0 1/u(POWER) switch Number buttons Controlling TVs with the remote 1 Slide TV/DVD switch to TV. 2 Hold down 1/u (POWER), and enter your TV’s manufacturer’s code (see the table) using the number buttons. Then release 1/u(POWER). Code numbers of controllable TVs If more than one code number is listed, try entering them one at a time until you find the one that works with your TV. Notes • If you enter a new code n...