Évaluations - 0, GPA: 0
(
)
)
|
Par ce dispositif a également d'autres instructions :
Facilité d'utilisation
Use either of the following battery pairs: Two AAA alkaline batteries Two AAA nickel-metal hydride (Ni-MH) batteries* Batteries are not included. 1 Press the battery compartment cover in the direction illustrated to open it. 2 Insert the batteries into the battery compartment as marked inside. Make sure the batteries are installed correctly. 3 Close the cover. Do the reverse procedure to open the cover. ... . . ... .. . . . .. . . .. Notes compartment cover. Careless handling may cause injury. Checking batteries When the POWER lamp lights up red, Sony recommends that you replace the POWER lamp is red. However, charging takes longer than usual. If neither the CHG lamp nor the POWER lamp lights up when the shoe POWER switch is set to [ON], check if the batteries are installed correctly. If the batteries are installed correctly but the lamps still do not light up, replace the batteries. Attaching this unit to your camera and turning it on (see illustration .) 1 Make sure that the shoe POWER switch of this unit is set to [OFF]. If it is not, set it to [OFF]. 2 the down position. 3 Slide the mounting foot of this unit into the accessory shoe of your camera in the direction of the arrow until it locks. When this unit is properly attached to the shoe, it automatically locks. To remove this unit, press the mounting-foot release button and slide the mounting foot in the opposite direction to the attaching procedure. (see illustration .-3-.) 4 Turn your camera on. 5 Turn this unit on. up. .-5-.) Power save DSLR-A100). To exit the power saving state, turn this unit back on or operate your camera. Shooting 1 Make sure that your camera and this unit are turned on. 2 Set your camera to the desired shooting mode. Refer to the operating instructions of your camera for shooting modes. When you set your camera to shutter speed priority (S) mode or manual exposure * 3 After charging of this unit is completed, press the shutter button to shoot a subject. When charging is completed, the CHG lamp of this unit turns amber. blinks amber. Notes If you shoot before charging is completed, you may not be able to get enough lighting (under exposure). before pressing the shutter button. lighting conditions. Overheat protection Overheat protection is a function for protecting this unit from overheating. If this unit automatically disabled. When overheating is detected, the POWER lamp blinks in red at one-second intervals. When this unit is in an overheated state, leave it without any operation for 10 minutes to cool down. . BOUNCE Switch the wall (see illustration .-.) .-.). In outdoor shooting, setting the BOUNCE switch to [DIRECT] lets you illuminate a Slide the BOUNCE switch to the desired position (see illustration . -1). Notes Make sure you slide the BOUNCE switch until the A mark is aligned with the desired position mark. ceiling or glass. (the shot looks dark), get closer to the subject, increase the ISO sensitivity or open the aperture more. . TELE Switch [Tele position] (see illustration . range. Notes Set the TELE switch to [Standard position] for regular shooting. B mark is aligned with the desired position. illuminator, AF accuracy may be greatly reduced in night view shooting. Wireless Control used separately from a camera. 1 Connect this unit to your camera, and set the power switches of 2 Camera: Set the mode to [Wireless]. Refer to the operating instructions of your camera for details. 3 4 5 of your camera. 6 and press the shutter button fully down to shoot. Notes Lighting ratio control setting (RATIO) is not available. Auto WB Adjustment with Color Temperature Info White balance is automatically adjusted based on color temperature information sent except the DSLR-A100). camera. Maintenance . . . . . . . .. .. . . . .. . .. . . .. . Compatibility our website: Notes on Use During shooting and deterioration of this unit and its batteries. naturally for at least 10 minutes. Do not carry your camera by holding this unit when it is attached. Always hold the camera itself. When changing the shoe POWER switch to the [OFF] position, be careful not to Batteries red. date of production. careful when touching the batteries because they may be hot, depending on the battery type and conditions of use. Remove and store the batteries if you do not intend to use this unit for a long time. Temperature Do not expose this unit to extremely high temperatures (e.g. in direct sunlight inside a vehicle) or high humidity. A drastic temperature change may cause condensation inside this unit. When place, leave it for a while until it reaches room temperature and then remove it from the bag. Battery output decreases as temperature decreases. When using in a cold environment, use new batteries or prepare spare batteries kept warm and use them a cold environment even though the batteries still have remaining capacity. If the battery output becomes low due to low temperature, leave the batteries indoors from water or sand. Any wat...