Évaluations - 2, GPA: 4.5 ( )

Fabricant : Bolens Taille : 1.9 mb Nom Fichier : e002589b-aa18-4ebf-a748-99aeb85cf003.pdf Langue d'enseignement:

Mow across the face of slopes, never up-and-down. Exercise extreme caution when changing direction on slopes. Do not mow excessively steep slopes. Always be sure of your footing. A slip and fall can cause serious personal injury. 10. Never operate mower without proper guards, plates or other safety protective devices in place. 11. Muffler and engine become hot and can cause a burn. Do not touch. 12. Do not operate this mower with the chute door open, unless the complete grass catcher or chute deflector is properly mounted on the mower. A" MAINTENANCE AND STORAGE 1. Check the blade and engine mounting bolts at frequent intervals for proper tightness. Also visually inspect blade for damage (e.g. bent, cracked). Replace with blade which meets original equipment specifications. 2. Keep all nuts, bolts, and screws tight to be sure the equipment is in safe working condition. 3. Never store the mower with gasoline in the tank or gas containers inside of a building where fumes may reach an open flame or spark (e.g. gas hot water heater). Allow the engine to cool before storing in any enclosure. 4. To reduce fire hazard, keep the engine free of grass, leaves and excessive oil. 5. Check the grass catcher bag frequently for wear or deterioratior Replace a worn or damaged bag immediately. For safety protection, replace only with new bag meeting original equipment specifications. 2 USE THIS SHEET AS A GUIDE TO DETERMINE SLOPES WHERE YOU MAY NOT OPERATE SAFELY. ................... i C> V •••- . ........ SIGHT AND HOLD THIS LEVEL WITH A VERTICAL TREE -------A POWER POLE *4------------A CORNER OF A BUILDING .............. o*1 I -----OR A FENCE POST I I I I........Ntz ! „ I .......... «/« ! ...... G) A * 0) (0 IT (D ...... g • • » <0 fi) O o Do not mow on inclines with a slope in excess of 15 degrees (a rise of approximately 2V2 feet every 10 feet). A riding mower could overturn and cause serious injury. If operating a walk-behind mower on such a slope, it is extremely difficult to maintain your footing and you could slip, resulting in serious injury. Operate RIDING mowers up and down slopes, never across the face of slopes. Operate WALK-BEHIND mowers across the face of slopes, never up and down slopes. I CONTENTS OF HARDWARE PACK/PARTS IDENTIFICATION Remove this sheet from your owner’s manual and lay the hardware on the illustration for identification purposes. After assembly, keep the Slope Gauge whici is on the reverse side of this sheet for future use. (Hardware pack may contain extra items which are not used on your unit.—Part numbers are shown in parentheses.) ATTACHING THE LOWER HANDLE Hairpin Clips (714-0104) B ATTACHING THE UPPER HANDLE Split Washers 5/16" I D. (736-01 19) Curved Head Bolts (710-0671) Hex Nuls 5/16-18 Th ead (712-026 7) ATTACHING THE STARTER ROPE Hex Lc ck Nut Vi-20 Thread (712- 3324) Rope Guide (710-1205) ATTACHING THE CABLE BRACKET AND THROTTLE CONTROL o Spring Washer Va" I.D. (736-0175) Hex Nut Vi-20 Thread (712-0287) Cable Bracket/^ (17174) Hex Elolt Vi-20 x 1-7 8" Long ^(710-1 >16) Blade Control Handle Upper Handle Rope Guide' Grass Catcher Handle Mount Bracket Throttle -Control Lower Handle Locking Lever Rear Deflector Model 436R Shown PARTS IDENTIFICATION ASSEMBLY OF GRASS CATCHER Œ Flat Washer 1/4" I.D. x 5/8" O.D. (736-0463) •Shoulder Íj Bolt Self-Tapping Screws (710-0892) Ü (738-0137) ^--S —Wave Washer ( \ 3/8" I.D. \\_y J (736-0286) Internal Star” Washer 1/2" I.D. (736-0498) ©~“! A / Locking Lever (720-0224) SECURING THE CABLES n --- ( able Ties (726-0240) I i I i I i I i I i I i I I I 0 INCHES ! i i i I i i I Cut AL This Line ASSEMBLY INSTRUCTIONS IMPORTANT: This unit is shipped WITHOUT GASOLINE or OIL. After assembly, service engine with gasoline and oil as instructed in the separate engine manual packed with your unit. NOTE: Reference to right or left hand side of the mower is observed from the operating position. Refer to parts identification on page 4 for location of parts when assembling the mower. Tools Required for Assembly (1) Pair of Pliers (1) 1/2" Wrench* (2) 7/16" Wrenches* *Or two 6" Adjustable Wrenches Hole in Blade Control Handle Washer FIGURE 2. UNPACKING 1. Remove the lawn mower from the carton by opening the top flaps and lifting the unit out. Be careful of the staples. Make certain all parts and literature have been removed from the carton before the carton is discarded. 2. Disconnect the spark plug wire and move away from the spark plug. 3. Stretch out all control cables and place on the floor. Be careful not to bend or kink the cables at any time during assembly. 4. Remove page four from this manual and lay the contents of the hardware pack on the illustration for identification. ATTACHING THE LOWER HANDLE (Hardware A) 1. Attach th...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :