Évaluations - 4, GPA: 4.5
(
)
)
|
Facilité d'utilisation
3 OPERATION.................................................................6 MAINTENANCE............................................................7 STORAGE..................................................................... 7 SERVICE AND ADJUSTMENTS..................................8 TROUBLESHOOTING.................................................. 8 REPAIR PARTS EXPLOSION....................................10 REPAIR PARTS LIST.................................................11 SAFETY Any power equipment can cause injury if operated improperly or if the user does not understand how to operate the equipment Exercise caution at all times, when using power equipment. 1. Read the vehicle and sweeper owners manuals and know how to operate your vehicle and sweeper before using this sweeper attachment. Always instruct other users before they operate the sweeper. 2. Do not permit children to operate sweeper. 3. Do not permit anyone to ride on sweeper. 4. Never attach the hopper rope to any part of your body or clothing! Never hold onto the rope while towtng the sweeper! Attach the rope to the towing vehicle to keep it away from wheels and rotating parts. 5. Operate the sweeper at reduced speed on rough terrain, near ditches and on hillsides to prevent loss of control. 7. 8. a attachment of this sweeper. Do not fill sweeper to maximum capacity without checking the capability of the towing vehicle to safely pull and stop with the sweeper attached. Stay off of sleep slopes. Stop and inspect vehicle and sweeper for damage after striking an object. Repair any damage before continuing operation. Keep sweeper away from fire. Excessive heat can damage the brushes and hopper bag and could cause the bag and its contents to bum. Before storing the sweeper, always empty the hopper bag to avoid spontaneous combustion. 10. Follow maintenance and lubrication instructions as outlined in the maintenance section of this manual. A Look for this symbol to point out important safety precautions* It means-Attention!! _Become alert I? Your safety is involved. ASSEMBLY CARTON CONTENTS 1. Sweeper Assembly 2. Brace Rods (2) 3. Rope 4. Hopper Assembly HARDWARE FOR ASSEMBLY Hardware is preassembled to sweeper and hopper. TOOLS REQUIRED (l) 1/2" Wrench 1. Remove the nuts, lock washers and bowed washers from the two curved head bolts, leaving the bolts in the tube at the front of the sweeper housing. See figure 1. 2. Loosen the knob fastening the height adjustment handle to the height adjustment strap. See figure 1. 3. Place the base of the height adjustment handle onto the two curved head bolts and secure it with the bowed washers, lock washers and hex nuts that you removed. See figure 1. 4. Attach the ends of the lower hopper tubes to the Inside of the side hopper tubes using the two 3/8* x 1/2" clevis pins and 3/32" hair cotter pins which came preassembled to the tubes. See figure 2. HOPPER BAG BOTTOM FIGURE 1 FIGURE 2 IMPORTANT; Do not over bend the support rods during the following step. Over bending will cause the spring steel rods to loose supporting tension. 5. Assemble the two hopper support rods as shown in figure 3» Place one end of a rod into the hole in an upper hopper tube and bend the rod just enough to fit the bottom end of the rod into the hole in a bottom hopper tube. HINT: To ease assembly of the rods, tip the hopper bag back so that the rear of the bag rests on the ground. 7. Assemble the hopper bag to the sweeper by sliding the ends of the bag arm tubes into the ends of the hitch tubes. Secure with two 1/4“ x 1-1/2" clevis pins and 3/32” hairpin cotters that came preassembled to the hitch tubes. See figure 5. FIGURE 5 FIGURE 3 6. Secure the rope around the middle of the upper hopper tube as shown in figure 4. FIGURE 4 ATTACHING SWEEPER HITCH TO TRACTOR 1. Place the tractor and sweeper on a flat level surface. 2. Measure the height of the tractor hitch. Refer to GROUP “A* and GROUP "B“ drawings below to determine if the sweeper hitch brackets are mounted correctly for your tractor or if the top and bottom brackets need to be switched. 3. Set the sweeper height adjustment handle to about the middle of its adjustment range. 4. Attach the sweeper hitch to the tractor hitch, arranging the 3/4* spacers into one of the six possible combinations shown in GROUP A and GROUP B diagrams below. IMPORTANT: To obtain the best performance from your sweeper, arrange the spacers so that the sweeper bag is approximately level with the ground and approximately 5" to 7" off the ground as shown in figure 6. GROUP “A" - For vehicles with hitches having 8" to 10" ground clearance. BRUSH HEIGHT ADJUSTED APPROXIMATELY LEVEL (5n to 7” FROM SURFACE) FIGURES GROUP "B" - For vehicles with hitches having 10” to 13” ground clearance. N HITCH BRACKET MOUNTED ABOVE HfTCH TUBES BLACK UNE IS TRACTOR HITCH BLACK UNE IS TRACTOR HITCH OPERATION KNOW YOUR SWEEPER PIVOT ROD SAG ARM TUBE HEIGHT...