Évaluations - 5, GPA: 4.2
(
)
)
|
Facilité d'utilisation
1700259. Located on Blower. I A warning! sn DO NOT OPEN COVER WITH ENGINE RUNNING. DO NOT OPERATE ENGINE WITHOUT COMPLETE CATCHER IN PLACE. Part No. 1676923. Located on Cart (Installed During Setup). A WARNING DO NOT USE THIS HOLE FOR DRAWBAR. TRACTOR TIP OVER MAY OCCUR. Part No. 1700346. Located on Bracket (Installed During Setup). OPERATORS MANUAL MOWER DRIVEN VACUUM COLLECTOR BLOWER ASSEMBLY MFG. NO. 1691260 CART COLLECTOR MFG. NO. 1691187 MFG. NO. 1691320 file 1'^' FORM - 1679658 PRINTED IN U.S.A. 8610 1 Safety Rules Read these safety rules and the safety rules in your Operator’s Manual and follow them closely. Failure to obey these rules could result in loss of control of vehicle, severe personal injury to yourself, or damage to property or equipment. The triangle ^ in the text signifies important cautions or warnings which must be-followed. 1. Know the tractor’s controls and how to stop quickly. READ THE TRACTOR’S OWNERS MANUAL. 2. Shut the tractor’s engine (motor) off before attaching, adjusting, or disconnecting the Cart Collector. 3. Check the mounting bracket to make sure it is bolted tightly to the tractor’s drawbar and back plate. 4. Always secure the Cart Collector to the bracket with two clevis pins and two hairpin cotters. 5. Check the latch handle to make sure it is engaged so the cart’s box is locked to the frame. 6. Allow room for the Cart Collector when turning and backing. Look behind to make sure the area is clear before backing up. 7. DO NOT turn sharply when the Cart Collector is alongside a building or any object. 8. DO NOT back and turn the Cart Collector in soft ground. When the wheel is buried in dirt, the swivel cannot turn and may be damaged. Always travel forward through soft ground. 9. DO NOT move loads in the Cart Collector in excess of 250 pounds. 10. DO NOT carry passengers in the Cart. CAUTION: 11. For added tractor stability and to prevent tipping or loss of control when using the Cart Collector: A. DO drive in reduced speed on uneven ground and when turning corners. B. Reduce loads on hillsides. It is recommended that the Cart Collector be kept only half full when negotiating any slopes. Start mowing on slopes when the Cart Collector is empty. C. DO NOT tow the Cart Collector on slopes steeper than 15 degrees. Mow up and down the face of slopes; never across the face of any slope. 12. CAUTION: Objects may be thrown from mower. For your safety: A. DO NOT open the door of the Cart Collector while the mower blades are turning. Shut off the tractor’s engine before opening the door or removing the grass chute. B. Be sure the complete Cart Collector is in place (door closed and grass chute connected) before operating the tractor’s mower. C. DO check the cart cover frequently for wear and tear. Replace with new cover for safety protection. 13. For best results when mowing grass: Set the mower to cut from 1 to 2 inches of grass. If grass is exceptionally tall, set your mower as high as possible for first cutting. Lower cutting height at succeeding cuttings until proper height is reached. It may be necessary to mow tall grass at a slower tractor speed. 2 INSTALLATION - BLOWER ASSEMBLY 1. Remove the right-hand arbor cover (A, figure 1) by removing bolts, washers and nuts in front that hold cover to deck. Also, remove nut (B) and washers that secure rear tab to arbor. 2. Slip mower belt off the right hand pulley. Remove the pulley from the arbor by removing capscrew and washers. Save washers for re-installation. Use wood block to prevent blade from turning. A. Arbor Cover B. Nut Cover Remove two self-tapping screws from arbor and install two 5/16 - 18 x 1-1/4 capscrews (A, figure 2). Tighten the capscrews. Figure 2. A. Capscrews B. Arbor Bracket C. Notch D. Arbor Pulley E. Belt Stop, Front 4. Install the arbor bracket (B, figure 2) as shown in figure 3. Note different holes for 42" and 48" mowers. Note belt stop (C, figure 3) is also installed. (Tighten nut that secures belt stop snug only - will be adjusted later.) A. Nut., 5/16 B. Washer, 5/16 C. Belt Stop D. Washer, 5/16 E. Locknut, 5/16 F. Arbor Bracket G. Capscrew, 5/16 -18x1-1/4 H. Lockwasher, 5/16 5. Install the other belt stop (E, figure 2) onto the other capscrew installed in step 3 with 5/16 washer, 5/16 lockwasher and 5/16 nut (snug). 6. Install new arbor pulley (D, figure 2) with hub down. Use new 7/16 - 14 x 2-1/4 capscrew and washers removed in step 2. Torque to 55 to 60 ft. lbs. Use wood block to prevent blade from turning. 7. Slip the mower drive belt onto the lower groove of the new pulley (D, figure 2). With the belt engaged, adjust the belt stops 1/8" from belt. Tighten the hardware. NOTE The belt for the 42" mower is part number 1679717 and is 32" long. The belt for the 48" mower is part ■ number 1678600 and is 33-1/2" long. 8. The blower belt (A, figure 4) is installed for use with 42" mower. For use with 48" mower, replace belt with the other b...
Ce manuel est également adapté pour les modèles :Gazonouborschiki - 1691187 (1.21 mb)