Évaluations - 3, GPA: 3.7 ( )

Fabricant : Empire Comfort Systems Taille : 3.61 mb Nom Fichier : Langue d'enseignement:

Release knob and it will pop back up. Pilot should remain lit. If it goes out, repeat steps 4 though 8. • If knob does not pop up when released, stop and immediately callyou service technician or gas supplier • If the pilot will not stay lit after several tries, turn the gas control knob to "OFF" and call your service technician or gas supplier. 9. Attention! Gas control has an INTERLOCK latching device. When the pilot is initially lit and the safety magnet is energized (pilot stays "ON"), the INTERLOCK latching device becomes operative. If the gas control is turned to the "OFF" position or gas flow to the appliance is shut off, the pilot cannot be relighted until the safety magnet is de-energized (approximately 60 seconds). There will be an audible "click" when the safety magnet in the gas control is de-energized. Pilot can now be relighted. Repeat steps 4 through 8. 10. Turn gas control knob counterclockwise to "HIGH." 11. Turn on all electric power to the appliance (if applicable). 12. Set thermostat (gas control knob) to desired setting from "HIGH" to "LOW." LIGHTING INSTRUCTIONS CONTROL KNOB INDICATOR GAS CONTROL KNOB SHOWN IN “OFF” POSITION THERMOCOUPLE (LPG) PILOT THERMOCOUPLE (NATURAL) 1. 2. Set thermostat (gas control knob) to lowest setting. Turn off all electric power to the appliance if service is to be performed (if applicable). 3. Push in gas control knob slightly and turn clockwise to "OFF." Do not force. TO TURN OFF GAS TO APPLIANCE 23099-1-0707 Page 19 VFDM(18,24,30)LB LIGHTING INSTRUCTIONS FOR YOUR SAFETY READ BEFORE LIGHTING WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. A. This appliance has a pilot which must be lighted by hand. When lighting the pilot, follow these instructions exactly. B. BEFORELIGHTING,smellallaroundtheappliancearea for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor. WHAT TO DO IF YOU SMELL GAS • Do not try to light any appliance • Do not touch any electrical switch; Do not use any phone in your building • Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's instructions. • If you cannot reach your gas supplier, call the fire department. C. Use only yourhand to push in orturn the gas control knob. Never use tools. If the knob will not push in or turn by hand, don't try to repair it, call a qualified service technician. Force or attempted repair may result in a fire or explosion. D. Do not use this appliance if any part has been underwater. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water. LIGHTING INSTRUCTIONS 1. STOP! Read the safety information above on this page. 2. Push in gas control knob slightly and turn clockwise to "OFF." Do not force. GAS CONTROL KNOB SHOWN IN “OFF” POSITION THERMOCOUPLE(LPG) THERMOCOUPLE(NAT) PILOT CONTROL KNOB INDICATOR 3. Wait ten (10) minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP! Follow "B" in the safety information above. If you do not smell gas, go to the next step. 4. Find pilot - the pilot is located in front of the rear log. 5. Turn manual gas control knob counterclockwise to "PILOT." 6. Push in manual gas control knob all the way and hold in. Repeatedly push the piezo ignitor button until pilot is lit (or use a match to light). Continue to hold the control knob in for about one (1) minute after the pilot is lit. Release knob and it will pop back up. Pilot should remain lit. If it goes out, repeat steps 2 through 6. • If knob does not pop up when released, stop and immediately callyou service technician or gas supplier • If the pilot will not stay lit after several tries, turn the gas control knob to "OFF" and call your service technician or gas supplier. 7. Three heat settings can be selected by slightly depressing the manual gas control knob and turning the manual gas control knob counterclockwise to 1, 2 or 3. 8. CAUTION! WHen the manual gas control knob has been turned to desired heat setting, ensure that the manual gas control knob is locked into that heat setting and cannot be turned without being depressed. If the manual gas control knob is in mid-position, between heat settings, incomplete combustion will take place, causing odor and may produce gas leakage or carbon monoxide. TO TURN OFF GAS TO APPLIANCE 1. Push in gas control knob slightly and turn clockwise to "OFF." Do not force. Page 20 23099-1-0707 23099-1-0707 Page 21 Figures 21 and 22 show a correct pilot flame pattern. The correct flame will be blue and will extend beyond the thermocouple. The flame will surround the thermocouple just below the tip. A slight yellow flame may occur where the pilot flame and main burner flame meet. Figures 23 and 24 show an incorrect pilot flame pattern. The incorrect pilot fla...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :