Évaluations - 2, GPA: 4
(
)
)
|
Facilité d'utilisation
The SwitchModule is available in several media configurations and in single-slot and dual-slot models. Before you unpack the SwitchModule, read Section 3.0, "Installation Prerequisites" and Section 5.0, "Installation Precautions". WARNING: CoreBuilder 5000 SwitchModules must be installed only by trained service personnel. 2.0 Learning About SwitchModules This document provides the basic information that you need to install and configure a 3Com CoreBuilder 5000 SwitchModule at software Version v3.0. For more detailed information about using the SwitchModule, see the following documents: ¦ CoreBuilder 5000 SwitchModule User Guide ¦ CoreBuilder 5000 Distributed Management Module User Guide for software Version v6.00 or later ¦ CoreBuilder 5000 Distributed Management Module Commands Guide for software Version v6.00 or later You can view these documents online with the 3Com DocsOnCD documentation CD-ROM that comes with this product. To order hard-copy documents, contact your network supplier, or call 3Com Corporation at 1-800-724-2447 and choose the Customer Operations option. 3.0 Installation Prerequisites Before you begin the SwitchModule installation process, read the hardware and software requirements in this section. In addition to reading this document, be sure to read the Release Note for CoreBuilder 5000 SwitchModules. 3.1 Tools Required You need a flat-blade screwdriver to install the CoreBuilder 5000 SwitchModule in the hub. 3.2 Hardware Prerequisites 1 Ensure that the CoreBuilder 5000 hub has at least one of the following management modules installed: ¦ 6000M-MGT Distributed Management Module, Version v6.00 or later ¦ 6000M-CMGT Advanced DMM/Controller Module, Version v6.00 or later 2 Ensure that the CoreBuilder 5000 hub has the following controller module installed: 6000M-RCTL Controller Module, Version v1.15 or later Part Number 10013592 COREBUILDER® 5000 SWITCHMODULE QUICK START AND REFERENCE 3 Ensure that the CoreBuilder 5000 hub contains either a PacketChannel or a SwitchChannel backplane. To verify that the hub has one of these backplanes, enter the command SHOW HUB. The model number displayed in the Hub Type field should end in C (SwitchChannel) or P (PacketChannel), and one of these backplanes should be listed under Backplane Type. For example: > show hub Hub Information: Hub Type: 6017C-AC Backplane Information: Backplane Type Revision Load-Sharing Power Distribution module 0 Enhanced TriChannel Backplane 1 RingChannel Backplane 0 SwitchChannel Backplane 2 If your hub does not have an installed PacketChannel or SwitchChannel backplane and you require communication among SwitchModules, contact 3Com or your 3Com representative to order a backplane upgrade kit. 4 Use the following table to determine the slot restrictions that apply to your hub configuration: Backplane Type Hub Type Installation Guideline PacketChannel 17-Slot Install SwitchModules in any slot. 10-Slot 7-Slot SwitchChannel (PacketChannel plus ATM Cell-Switching) 17-Slot Slots 9, 10, 11, and 12 are reserved for the CoreBuilder® 5000 ATM Switch/Control Point Module (Model Number 3C96416SW). 10-Slot Slots 9 and 10 are reserved for the CoreBuilder 5000 ATM Switch/Control Point Module (Model Number 3C96416SW). If you are installing only one SwitchModule, you can install it in any slot, including a reserved ATM slot. The single SwitchModule acts as a stand-alone switch. If your hub does not have an installed PacketChannel or SwitchChannel backplane, you can install only one SwitchModule per hub. 3.3 Software Prerequisites Before you install a new SwitchModule: 1 Determine the DMM module’s software version status. Enter the SHOW MODULE ALL command. > show module all The following display appears: Slot Module Version Network General Info ---------- ------ ------- ------------ 10.01 6100D-MGT v1.00 ETHERNET_1 11.01 6000M-RCTL v1.15 N/A Active Ctrl Module 12.01 6000M-ARCTL v1.15 N/A Stndby Ctrl Module 12.02 6000M-AMGT v6.00 N/A Master Mgmt Module 2 Look in the Version column to get the DMM software version. The new SwitchModule functions incorrectly if the DMM software version is wrong. As shown in the previous display example, the Advanced DMM/Controller (Model Number 6000M-CMGT) appears as two modules in the same slot (Model Numbers 6000M-ARCTL and 6000M-AMGT). The DMM operational code version is displayed in the Version field of the -AMGT module. 4.0 Crucial Download Procedure Review the following procedures before you attempt to download software to any SwitchModule in your hub. You must use the following procedures if you have 66xx family SwitchModules installed in your hub. 4.1 Download Procedure for SwitchModules Earlier than Version v2.02 and DMMs Earlier than Version v5.00 Use the following procedure for all SwitchModules in your hub that are earlier than Version v2.02, and DMMs that are earlier than Version v5.00. CAUTION: All bridge port communication ceases if you use an incorrect download procedure to upgrade your SwitchModule...
Ce manuel est également adapté pour les modèles :Alimentation et alimentation - COREBUILDER 5000 (210.29 kb)