Évaluations - 3, GPA: 3.7 ( )

Fabricant : Craftsman Taille : 1.36 mb Nom Fichier : Langue d'enseignement:

TAINERS, USE CLEAN FILL FUNNELS. 6 TO START ENGINE 1, Attach spark ptug wire and boot to spark plug 2. Place the throttle control lever in START position See figure 8 3. Grasp starter handfe (see figure 9) and pull rope out slowly until engine reaches start of compression cycle (rope will pull slightly harder at this point). Let the rope rewind slowly NOTE: A noise will be heard when finding the start of the compression cycle This notice is caused by the flails and fingers which are part of the shredding mechanism falling into ptace, and should be expected, 4 Pull rope with a rapid, continuous, full arm stroke Keep a firm grip on start handle Let rope rewind slowly. Do not let starter handle snap back against starter, 5, Repeat preceding instructions 3 and 4 until engine fires, 6, After engine starts, move throttle control lever on engine to slow position for a few minutes warm up, Then move throttle control lever to RUN position for shredding-chipping operations ""-" ......... _ Air -i .Screen FIGURE 9. TO STOP ENGINE 1 Move throttle control lever to STOP position See figure 8 2, Disconnect spark plug wire from spark p_ug and ground against the engine to prevent accidental starting while equipment is unattended HOW TO USE YOUR CHIPPER-SHREDDER Your shredder is designed for safe, efficient operation. KEEP HANDS AND FEETAWAY FROM ALL OPENINGS WARNING Wear the safety glasses provided with your unit while operating the chipper- shredder to prevent injury from any chips which may be ejected out of the openings, Make certain chip-it guide is closed when not in use, Wear gloves when handling material Feed material into the chipper-shredder at a steady rate It is possible to feed too fast° Experiment with feeding rates to determine what rate provides the best results without stalling the engine or plugging the discharge chute. The discharge chute will direct the shredded material into a pile, a container or the bag provided with your shredder i wARN, G I The chipper-shredder discharges material with considerable velocity Keep away from the area around the discharge chute Always stop the engine and d_sconnect the spark plug wire when removing or attaching the bag when changing containers or when removing the shredded material if if becomes necessary to push materials into the chipper-shredder, use a small diameter stick, NOT YOUR HANDS The stick sl_ould be small enough that it will be ground up if it gets into the impeller assembly. Do not deposit material larger then 12" diameter in the hoppe_ or upper guide extension Any material heavier then 1/2" should be fed _nto the chip-it guide Leaves and smaller branches can be fed into the hopper with the leaf ramp raised as shown in figures 10 and 11 Hopper Chip-it Guide FIGURE 10. No larger than 112 inch diameter )or Chip-it Leaf Ramp FIGURE 11 Lower the leaf ramp by holding the handle and pulling up on the release bar See figure 12 Leaves and small twigs can be raked into the chipper-shredder with the leaf ramp in this position See figure 13 Leaf Ramp Handle \ FIGURE 12. Leaf Ramp ,_( FIGURE 13o No larger than 1t2 inch diameter Elastic > Lock Nuts FIGURE 14. Bulky material, such as stalks or heavy branches (anything over tt2" diameter), should be fed into the chip-it guide.. See figure 15. Do not force or jam material into the chip-it guide Make certain leaf ramp is raised as shown in figure 15 when using the chip-it guide Make certain chip-it guide door is closed when not in use Keep Leaf Ramp Raised When Using Chip-It Guide Small branches can also be fed into the leaf ramp See figure 14 FIGURE 15, ADJUSTMENTS CARBURETOR ADJUSTMENT If any adjustments are made to the engine while the engine if running {eg. carburetor), keep clear of all moving parts Be careful of heated surfaces and muffler Minor carburetor adjustment may be required to compensate for differences in fuel, temperature, altitude or toad NOTE A DIRTY AIR CLEANER WILL CAUSE ENGINE TO RUN ROUGH BE CERTAIN AIR CLEANER IS CLEAN AND ATTACHED TO THE CARBURETOR BEFORE ADJUSTING CARBURETOR DO NOT MAKE UNNECESSARY ADJUSTMENTS FACTORY SETTINGS ARE SATISFACTORY FOR MOST APPLICATIONS AND CONDITIONS. Never attempt to change maximum engine speed It is pre-set at the factory and should be changed only by a qualified service technician who has the necessary equipment, The carburetor may need re-adjusting if engine lacks power or does not idle properly if adjustments are needed, proceed as follows. To Adjust Carburetor: 1. Close needle valve (See figure 16) clockwise (("_ } finger tight only Forcing may cause damage_ Then open 1-!/2 turns counterclockwise (r'x) 2. Start engine and allow to warm for five minutes. 3 With throttle in RUN position, close needle valve clockwise (;-_,) until engine starts to lose speed (lean mixture). Then slowly open needle valve counterclockwise (f'_) until engine JUST BEGINS to run unevenly This mixture should be rich enough for best performance under load. Place throttle control in IDLE pos...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :