Évaluations - 3, GPA: 4.3
(
)
)
|
Facilité d'utilisation
Please remove A all urethane supports and packaging materials before operating the unit. Failure toi^ remove all packaging materials may lead to a fire and / or damage to the appliance. 3 1. Remove all external packaging that is protecting top portion of unit. 2. Remove unit from shipping container while in the upright position. The unit can be lifted out of the carton by grasping under the conveyor on each side of the appliance. Please remove the plastic bag. 3. Remove all internal packaging to the unit. Important: Remove urethane supports located inside the tunnel oven between the top heaters and the conveyor. Remove tape from conveyor trays. Remove tape from extrusion corners. Remove tape from deflecting curtains located just above entrance and exit of conveyor. 4. Visually inspect all external and internal portions of unit for damage. Important: Inspect the top white ceramic elements located inside the oven tunnel after removal of urethane supports. To inspect these white ceramic elements, use a small mirror held under each element to detect cracks. Important: The Ceramic elements are fragile and will break under stress. Do not twist, pull, push, or otherwise subject the white ceramic elements to stress. 5. Wipe down the exterior of the unit using a damp cloth with warm water. Do not use abrasive pads or cleaners as they will damage the stainless steel surface and high temperature plastic. NOTE: DO NOT USE CLEANERS OF ANY KIND ON THE WHITE CERAMIC HEATERS. 6. Remove four feet from box and install into threaded nuts located at the four corners underside of the left and right housings; Also remove conveyor extension tray(s). Conveyor extensions should be hung offend of conveyor frame. As ourstandard, Model XWAV1417A will only have one extension intended for the exit end. 7. Place unitin operating location. Note: Ambient Conditions - Make sure that the operating location is in an area where the ambient temperature is held constant (minimum 70°F). Please avoid areas such as near exhaustfans and airconditioning ducts. Warning: Operating environment Ensure that operation location is at a reasonable distance from combustible walls and materials otherwise combustion or discoloration could occur. Stand-off/Air-divider located on rear panel is important in maintaining proper division of inletand exhaust airflow- If removed it could resultin improperfunctioning of unit and MAY cause personal injury and WILL void vour warranty. Caution: Operating environment Place unit on a stable, level counter at a convenient height for use. Turn the adjustable feet so that unit is level to countertop. The top of the unit is not intended for use a shelf. Materials placed there are at riskforfire. 8. Before plugging unit into wall, make sure that the switch is in the off position. 9. Warning: Ensure no hands, tools or parts or other unintended items are located on the conveyor as injury will result when unit is turned on. 10. Plug unit into grounded electrical outletwith correct voltage, and plug configuration. Warning: Using any receptacle that is not designed to match the attached cord and plug MAY cause personal injury and WILL void yourwarranty. IMPORTANT FOR FUTURE REFERENCE Please complete this information and retain this manual for the life of the equipment. For Warranty Service and/or Parts, this information is required. Model Number Serial Number Date Purchased 4 Oven Stacking FIGURE 1 The stacking kit will consist of 4 corner posts to be inserted between stacked units. Warning: When stacking, unit must have proper stacking kit installed. This will prevent overheating and damaging of electrical components. Warning: Do not stack more than three units tall or do not use more than two stacking kits. Warning: Standoff on rear panel of unit is important to allow proper inlet and exhaust fan airflow. Do not cover inlet or exhaust fan openings as this could damage electrical components. 1. Ensure bottom unit is mounted on secure surface, with feet installed. 2. Remove respective corner end caps and screws. This will allow each of the stacking spacer retaining fingers to slide into the extrusions. 3. Remove the feet from the top unit as shown. 4. Secure each stacking spacer to the bottom of the unit as shown by using the bolts and washers provided. You should have four total of each. 5. Once the stacking kit spacers are secure, place top unit onto bottom unit. The stacking kit spacers each have tapered guides to allow the unit to lock into position. 6. Refer to Figure 1. Install rear support bracket and screws as shown. Each stacking kit requires that two brackets be mounted on the backside only. One bracket near the strain relief and one atthe opposite end. 7. Refer to Cleaning Instructions for cleaning of stacking spacers and cleaning between units. y Remove End Caps & Screws Before Installing Kit - 5. OPERATION 1. The controls that operate the unit, heaters and conveyor are ...