Log:
Évaluations - 3, GPA: 3.7 ( )

Instructions Sears, Modèle 8MPL100J20B1

Fabricant : Sears
Taille : 2.69 mb
Nom Fichier :
Langue d'enseignement: en
Aller à la télécharger



Facilité d'utilisation


Safe Installation Requirements FIRE, EXPLOSION, AND ASPHIXIATION HAZARD Improper adjustment, alteration, service, maintance or installation could cause death, personal injury, and/or property damage. Installation or repairs made by unqualified persons could result in hazards to you and others. Installation MUST conform with local codes or, in the absence of local codes, with codes of all governmental authorities having jurisdiction. The information contained in this manual is intended for use by a qualified service agency that is experienced in such work, is familiar with all precautions and safety procedures required in such work, and is equipped with the proper tools and test instruments. NOTE: This furnace is design-certified by the CSA International (formerly AGA and CGA) for installation in the United States and Canada. Refer to the appropriate codes, along with this manual, for proper installation. Use only the Type of gas approved for this furnace (see Rating Plate on unit). Overfiring will result in failure of heat exchanger and cause dangerous operation. (Furnaces can be converted to LP gas with approved kit.) • Install this furnace only in a location and position as specified in "2. Installation"of these instructions. • Provide adequate combustion and ventilation air to the furnace as specified in "4. Combustion and Ventilation Air" of these instructions. Combustion products must be discharged outdoors. Connect this furnace to an approved vent system only, as specified in "5. Gas Vent lnstallation, 6. Horizontal Venting and 7. Masonry Chimney Venting"of these instructions. Never test for gas leaks with an open flame. Use a commercially available soap solution made specifically for the detection of leaks to check all connections, as specified in "8. Gas Supply and Piping, Final Check"of these instruc tions. Always install furnace to operate within the furnace's intended temperature-rise range with a duct system which has an external static pressure within the allowable range, as specified in "Technical Support Manual" of these instructions. See furnace rating plate. • When a furnace is installed so that supply ducts carry air circulated by the furnace to areas outside the space containing the furnace, the return air shall also be handled by a duct(s) sealed to the furnace casing and terminating outside the space containing the furnace. • A gas-fired furnace for installation in a residential garage must be installed as specified in "2. Installation"of these instructions. • This furnace is not to be used for temporary heating of buildings or structures under construction. See "2. Installation, Item 10'_ • This furnace is NOT approved for installation in mobile homes, trailers or recreation vehicles. • Seal around supply and return air ducts. • Install correct filter type and size. • Unit MUST be installed so electrical components are protected from direct contact with water. Safety Rules Your unit is built to provide many years of safe and dependable service providing it is properly installed and maintained. However, abuse and/or improper use can shorten the life of the unit and create hazards for you, the owner. A. The U.S. Consumer Product Safety Commission encourages installation of carbon monoxide alarms. There can be various sources of carbon monoxide in a building or dwelling. The sources could be gas-fired clothes dryers, gas cooking stoves, water heaters, furnaces, gas-fired fireplaces, wood fireplaces. Carbon monoxide can cause serious bodily injury and/or death. Carbon monoxide or "CO" is a colorless and odorless gas produced when fuel is not burned completely or when the flame does not receive sufficient oxygen. Therefore, to help alert people of potentially dangerous ca rbon monoxide levels, you should have a commercially available carbon monoxide alarm that is listed by a nationally recognized testing agency in accordance with Underwriters Laboratories Inc. Standard for Single and Multiple Station Carbon Monoxide Alarms, ANSI/UL 2034 or the CSA 6.19-01 Resi dential Carbon Alarming Devices installed and maintained in the building or dwelling concurrently with the gas-fired furnace installation (see Note below). The alarm should be installed as recommended by the alarm manufacturer's installation in structions. B. There can be numerous sources of fire or smoke in a building or dwelling. Fire or smoke can cause serious bodily injury, death, and/or property damage. Therefore, in order to alert people of potentially da ngerous fire or smoke, you should have fire extinguisher and smoke alarms listed by Underwriters Laboratories installed and maintained in the building or dwelling (see Note below). Note: The manufacturer of your furnace does not test any alarms and makes no representations regarding any brand or type of alarms. C. To ensure safe and efficient operation of your unit, you should do the following: 1. Thoroughly read this manual and labels on the unit. This will help you understand...

Ce manuel est également adapté pour les modèles :
électrique - 8MPL100F20B1 (2.69 mb)
électrique - 8MPL075F16B1 (2.69 mb)
électrique - 8MPL050B12B1 (2.69 mb)
électrique - N8MPN125J22B1 (2.69 mb)

Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories