Évaluations - 2, GPA: 4.5 ( )

Fabricant : Well Traveled Living Taille : 1.46 mb Nom Fichier : Langue d'enseignement:

If a damaged part is detected, do not operate until an original equipment replacement part has been properly installed. Use of unauthorized parts will void warranty and create an unsafe condition. • Do not attempt to use this appliance without a functional factory-supplied gas regulator in place. If regulator becomes damaged, use only a factory-supplied replacement. • During operation, do not touch burner assembly. The surface of heater's emitter can reach temperatures approaching 1600°F. • After shutdown, do not touch burner assembly until heater has cooled completely (approximately 45 minutes after use). 7 TABLETOP HEATER LOCATION • The tabletop heater is for outdoor use only. Always ensure that adequate fresh air ventilation is provided. • Always maintain proper clearance to combustible materials, i.e. top 18” and sides 24” minimum. • Tabletop heater must be located on a stable and strong surface. • Never operate heater in an explosive atmosphere like in areas where gasoline or other flammable liquids or vapors are stored. CHECKING FOR LEAKS Make 1-2 oz. of leak solution by mixing one part liquid dishwashing soap and 3parts water. Spoon several drops(or use squirt bottle ) of the solution onto the regulator/canister connections. Inspect the connections and look for bubbles. If NO bubbles appear, the connection is safe. If bubbles appear, there is a leak: • Loosen and re-tighten this connection. • Re-check for a leak. If you continue to see bubbles after several attempts, disconnect propane source. BEFORE OPERATING • I am familiar with entire owner's manual and understand all precautions noted in “Safety First”. • All components are properly assembled, intact and operable. • No alterations have been made. • All gas connections are secure and do not leak. • Wind velocity is below 10 mph. • Outdoor temperature is greater than 40 degrees F. • Heater is outdoors (outside any enclosure). • There is adequate fresh air ventilation. • Heater is away from gasoline or otherflammable liquids or vapors. • Heater is away from windows, air intake openings, sprinklers and other water sources. • Heater is at least 18 “clearance (top) and 24” clearance (side) from combustible materials. 8 • Heater is on a hard and level surface. • There are no signs of spider or insect nests. • All burner passages are clear. • All air circulation passages clear. • Children, pets, clothing, flammable materials and items that can be damaged from radiant heat are away from the heater. • Children and adults in the area have been alerted to the high temperature hazards; especially burns and clothing fires. • Children and adults in the area have been warned not to touch heater near emitter during operation and until unit has cooled completely. OPERATION Inspect the visible portion of the hose before each use of the appliance. Inspect the entire hose assembly at least annually. Before Turning Gas Supply ON Your heater was designed and approved for OUTDOOR USE ONLY. DO NOT use it inside a building, garage or any other enclosed area. Make sure surrounding areas are free of combustible materials, gasoline, and otherflammable liquids. • Ensure that there is no obstruction to air ventilation. • Be sure all gas connections are tight and there are no leaks • Be sure the access panel is clear of debris. • Be sure any component removed during assembly or servicing is replaced prior to starting. Before Lighting Heater should be thoroughly inspected before each use, and by a qualified service person at least annually. If relighting a hot heater, always wait at least 5 minutes for gas to dissipate. 9 Lighting 1. Make sure control knob is in the “Off” position. 2. Push in and rotate the Control Knob to“Pilot”position. Depress igniter button. 3. Once burner is lit, hold Control Knob in for at least 30 seconds and release. 4. If burner does not stay lit, turn control knob to“Off” position and wait 5 minutes and repeat 2 and 3. 5. Once burner is lit, rotate control Knob to desired heating level (LO: low ; HI: high). If you experience any ignition problem, turn off the heater and gas supply, and consult “Troubleshooting” on page 12. Caution Avoid inhaling fumes emitted from the heater's first use. Smoke and odor from the burning of oils used in manufacturing will appear. Both smoke and odor will dissipate after approximately 30 minutes. The heater should NOT produce thick black smoke. Note: The burner may be noisy when initially turned on. To eliminate excessive noise from the burner, turn the Control Knob to the LOW position. Then, turn the knob to the level of heat desired. When heater is ON: Emitter screen will become bright red due to intense heat. The color is more visible at night. Burner will display tongues of blue flame. These flames should not be yellow or produce thick black smoke, indicating an obstruction of airflow through the burners. If yellow flame is detected, turn off heater and...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :