Évaluations - 3, GPA: 4.3
(
)
)
|
Facilité d'utilisation
Keep young children away. • Turn off the gas supply at the gas container after use. • Any modification of the appliance may be dangerous. FOR YOUR SAFETY • Gas leaks may cause a fire or explosion and can cause serious bodily injury or death, or damage to property. • You must follow all leak checking procedures operating this unit. • Never use an open flame to check for leaks. WARNING Do not store or use gasoline or other flammable vapors or liquids in the vicinity of this or any other appliance. Danger Carbon monoxide hazard 1.This appliance can produce carbon monoxide which has no odor. 2. Using it in an enclosed space can kill you. 3. Never use this appliance in an enclosed space such as camper, tent, car or home. • Do NOT touch or move heater for at least 45 minutes after use. • Dome is hot to the touch. • Allow dome to cool completely before touching. 1 CONTENTS BREAKDOWN 2 Item No. Item Qty. Item No. Item Qty. 1 M6 Castle nut 3 11 Burner 1 2 Reflector 1 12 3/16" bolt 4 3 06mm Washer 3 13 M5x10mm bolt 1 4 Emitter screen 1 14 Tank Housing 1 5 Guard 1 15 Igniter button 1 6 Door Plate 1 16 Control knob 1 7 Base 1 17 Handle 1 8 Cast Iron weight 1 18 Regulator 1 9 M6x15mm bolt 4 19 60mm pin 3 10 3/16" bolt 4 20 M6 flange nut 3 SCREW PACKAGING LIST Item Qty. 3 6 M6 Castle nut 06mm Washer M6x15mm bolt 4 3/16" bolt 8 Item Qty. M5x10mm bolt & M5 nut 1 60mm pin 3 M6 flange nut 3 Wrench 1 ASSEMBLY PROCEDURE Tools needed: ( not included) • Adjustable opening wrench (2) 20 cm long • Slip joint pliers 23 cm long • Philips screwdriver w/medium blade • Teflon plumbing tape for joints 3 ASSEMBLY 1-1. Take out all the parts of the tabletop Heater. 1-2. Aim the cast iron at the holes on the base. 3-1. Put the burner on the tank housing then fix them with 4pcs 3/16” bolts. 2-1. Use 4pcs M6X15mm bolts to fix the tank housing to the base & cast iron. 2-2. Tighten the bolts as shown above. 4-1. Fix the regulator to the tank housing with the M5X10mm bolt & M5 nut. 4 5-1. Fix 3pcs pins of 60mm length to the emitter screen with 3pcs M6 flange nuts then tighten them. 6-1. Put the emitter screen on the burner. 6-2. Use 4pcs 3/16" bolts to connect the emitter screen to the burner. Tighten the bolts. 7-1. Put the guard on the burner over the emitter screen. 7-2. Put the ends of the guard into the holes of the burner. 8-1. Put 3pcs washers on each pins of the 60mm length. 5 10-1. Fasten the reflector with 3pcs M6 Castle nuts. 12-1. Close the door plate and lock it with the handle (rotate the handle 90 degrees). 11-1. Turn off the control knob of the burner. 11-2. Fix the 1.02Lbs gas tank (not included) to the regulator (rotate the gas tank clockwise toward the regulator until tightened.) rEP 10 6 SAFETY FIRST Read and become familiar with this entire manual, especially the following precautions. Caution: this appliance is for outdoor use only(outside any enclosure) Always make sure there is fresh air ventilation. • Use only outdoors in a well-ventilated space. Never use in a building, garage or any other enclosed area. • Always maintain at least 18“clearance(top)and 24”clearance (side) from combustible materials. • Always place heater on a hard and level surface. • Do not use if the wind velocity is greater than 10 miles per hour. • Unit will operate at reduced efficiency below 40°F (5’C). • Keep sprinklers and other water sources away from burner and controls. • Always use extreme caution when near heater. Alert both children and adults to the hazards of high temperatures , especially to avoid burns or clothing catching fire. • Young children and pets should be carefully supervised when they are in the area of heater. • Do not place clothing or other flammable materials either on or near heater. • Any guard or other protective device removed for servicing the heater must be replaced prior to operating the heater. • Certain materials or items, when stored under heater, will be subjected to radiant heat and could be seriously damaged. • Do not alter heater in any manner. • The pressure regulator and hose assembly supplied with the appliance must be used and replacements must be those specified by the manufacturer. • Inspect heater before each use. If a damaged part is detected, do not operate until an original equipment replacement part has been properly installed. Use of unauthorized parts will void warranty and create an unsafe condition. • Do not attempt to use this appliance without a functional factory-supplied gas regulator in place. If regulator becomes damaged, use only a factory-supplied replacement. • During operation, do not touch burner assembly. The surface of heater's emitter can reach temperatures approaching 1600°F. • After shutdown, do not touch burner assembly until heater has cooled completely (approximately 45 minutes after use). 7 TABLETOP HEATER LOCATION • The tabletop heater is for outdoor use only. Always ...
Ce manuel est également adapté pour les modèles :électrique - FireSense 60269 (1.46 mb)
électrique - FireSense 60270 (1.46 mb)