Apply a mixture of liquid soap and water to all joints. Bubbles forming show a leak that must be corrected. Correct all leaks at once. 6. Close propane supply valve. 4 Dayton Operating Instructions and Parts Manual Model 3VH20 Operation Review and understand the warnings in the General Safety Information section. They are needed to safely operate this heater. Follow all local codes when using this heater. TO START HEATER 1. Follow all installation, ventilation, and safety information. 2. Locate

Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or property damage! Retain instructions for future reference. ® Dayton Propane Construction Heater Description Dayton model 3VG81 is a 150,000 Btu/Hr propane construction heater with built-in thermostat. This heater uses propane gas for combustion. It is primarily intended for temporary heating of buildings under construction, alteration, or repair. This heater

Vent-free propane gas heaters, Models 2E783D and 3E467C, arewarrantedby DaytonElectricMfg. Co. (Dayton) to the original user against defects in workmanship or materials under normal use for one year after date of purchase. Any part which is determined by Dayton to be defective in material or workmanship and returned to an authorized service location, as Dayton designates, shipping costs prepaid, will be, as the exclusive remedy, repaired or replaced at Dayton's option. For limited warranty claim

IMPROPER INSTALLATION, ADJUSTMENT, ALTERATION, SERVICE OR MAINTENANCE COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE. REFER TO THESE INSTRUCTIONS FOR CORRECT INSTALLATION AND OPERATIONAL PROCEDURES. FOR ASSISTANCE OR ADDITIONAL INFORMATION CONSULT A QUALIFIED INSTALLER, SERVICE AGENCY OR THE GAS SUPPLIER. READ AND SAVE THESE INSTRUCTIONS Both Models Shown with Optional Floor Mounting Stand MODEL 2E783D MODEL 3E467C WARNING: if the information in this manual is not followed exactly,

Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or property damage! Retain instructions for future reference. ® Dayton Natural Gas Construction Heater Description Dayton Model 3VH19 heater is 100,000 Btu/Hr construction heater. This heater uses natural gas for combustion. It is primarily intended for the temporary heating of buildings under construction, alteration, or repair. This heater should never be use

Attach nut finger tight after inserting each screw. 5. After inserting all screws, tighten nuts firmly. Ventilation Follow the mini mum fresh, outside air ventilation requirements. If proper fresh, outside air ventilation is not provided, carbon monoxide poisoning can occur. Provide proper fresh, outside air ventilation before running heater. FRESH AIR OPENING REQUIREMENTS Square Feet Heater Size Opening 200,000 Btu/Hr 6.0 Provide a fresh air opening at least three square feet for each 100,000 B

Forany product believed to be defective within limited warranty, firstwriteorcaiidealerfromwhomproductwaspurchased.Dealerwillgiveadditional directions. If unable to resolve satisfactorily, write to Dayton at address below, giving dealer's name, address, date and number of dealer's invoice, and describing the nature of the defect. Title and risk of loss pass to buyer on delivery to common carrier. If product was damaged in transit to you, file claim with carrier. Manufactured for Dayton Electric

A fan attached to the other end of the motor pushes air through the heater. Part of the air enters the combustion chamber and mixes with the atomized fuel to form a combustible mixture. The rest of the air passes over and around the combustion chamber. At the front of the heater it mixes with the hot air coming from inside the combustion chamber. This results in a jet of clean, heated airflow-ing out of the front of the heater. 3. Ignition System. A transformer provides high voltage to a spark

Install the wheels (6) on the axle. IMPORTANT: The extended hub of the wheel should be positioned to- " ward the wheels support frame. Position the cap nuts (9) on the axle ends and gently tap with a hammer to secure. 2. Position the heater on the wheel support frame assembly with the combustion chamber end over the wheels. 3. Use four screws (7) and nuts (8) to attach the front handle to the top of the tank flange. The screws will go through the front handle, the tank flange and the wheel su

If you see globules of water in the bottom, drain and flush the tank and filter with clean fuel, b. Refill with fresh, clean fuel. FORM 5S1792 MODELS 2E510A, 2E511 A, 3E218A & 3E219 01582. Trouble Shooting Chart (Continued) SYMPTOMS POSSIBLE CAUSE(S) CORRECTIVE ACTION Heater burns, but puffs 2. Dirty air filters causing reduced 2. Remove and clean the air filters. of smoke can be seen; air flow through nozzle, resulting Be sure air intake is not blocked. heater will not burn in low