Évaluations - 3, GPA: 3 ( )

Fabricant : Regency Taille : 2.06 mb Nom Fichier : Langue d'enseignement:

BRICK FLUE BAFFLE & SECONDARY AIR TUBE INSTALLATION The flue baffle system located in the upper area of the firebox is removable to make cleaning your chimney system easier. The brick baffles must be installed prior to your first fire. Smoke spillage and draft problems may occur if the baffles are improperly positioned. Check the position of the brick baffles on a regular basis as they can be dislodged if too much fuel is forced into the firebox. The Large Stoves F3100L and S3100L are shipped with two of the secondary air tubes loose inside the firebox. They need to be installed after the brick baffle are installed. Follow the directions below. Large Stoves F3100L and S3100L The unit arrives with the first two air tubes (from the front) and the 2 baffle bricks on the floor of the firebox. The baffle bricks are positioned first and then the air tubes are installed. NOTE: If the first 2 airtubes are already installed in the stove, they must be removed in order to install the Brick Baffles. 1) Slide the left baffle brick over the two rear air tubes and then push it all the way to the left side of the firebox. Side View 2)Tilt the first Baffle Brick down and then slide the 2nd Baffle Brick up and back. Reposi- tion both baffle bricks flat on the air tubes. 3) Important: push both baffle bricks so they are tight against the side walls. Front View Regency Freestanding Woodstove INSTALLATION 4) Install the two front air tubes into the holes on the side channels. The notch goes on the right hand side with the air holes facing forward toward the door opening. If the tube will not slide in easily, simply use a pair of vise grips or pliers and tap it into place with a hammer. A tighter fit will ensure the tube will not move when the unit is burning. Note: When cleaning the chimney reverse the above procedures, removing the air tube and baffle bricks and then replace them when cleaning is completed. Medium Stoves F2100M and S2100M The unit arrives with the 2 baffle bricks on the floor of the firebox. 1) If all 3 air tubes are installed continue on to Step 2), if not, follow the instructions below. Install the air tube into the holes in the side channels. The notch goes on the right hand side with the air holes facing toward the door. Slide the tube into the left hand side, as far as possible and then bring it back into the hole on the right hand side until it locks into position. If the tube will not slide in easily, simply use a pair of vise grips or pliers and tap it into place with a hammer. A tighter fit will ensure the tube will not move when the unit is burning. See the diagram for the large air tube installation (page 15), though there are only three air tubes in the medium units. 2) Slide the left baffle brick over the air tubes from the front and then push it to the back. Side View 3) Tilt the left baffle brick up on top of the side channel and it will leave enough room to position the right baffle brick in the same manner as Step 1) above. Then reposition the left baffle brick flat on the air tubes. Front View 4) Important: push both baffle bricks so they are tight against the side walls. Front View Note: When getting the chimney cleaned, push the brick baffles forward toward the front of the stove, this should leave sufficient access to the flue. If it is not enough space then remove the middle air tube (reverse the procedure in step 1) above), and baffle bricks and then replace everything when cleaning is completed. Small Stoves F1100S 1) If the two air tubes are installed continue on to Step 2), if not, follow the instructions below. Install the air tube into the holes in the side channels. The notch goes on the right hand side with the air holes facing toward the door. Slide the tube into the left hand side, as far as possible and then bring it back into the hole on the right hand side until it locks into position. If the tube will not slide in easily simply use a pair of vise grips or pliers and tap it into place with a hammer. A tighter fit will ensure the tube will not move when the unit is burning. See the diagram for the large air tube installation (page 15), though there are only two air tubes in the small units. 2) Slide the left baffle brick over the front air tube and then slide it back over the rear air tube. Side View 3) Tilt the left baffle brick up on top of the side channel and it will leave enough room to position the right baffle brick in the same manner as Step 1) above. Then reposition the left baffle brick flat on the air tube. Front View 4) Important: push both baffle bricks so they are tight against the side walls. Front View Note: When getting the chimney cleaned, remove the baffle bricks for access to the flue, then replace them when cleaning is completed. Regency Freestanding Woodstove INSTALLATION BRICK INSTALLATION Firebrick is included to extend the life of your stove and radiate heat more evenly. Check to see that all firebricks are in their correct positions and have not becom...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :