(600 recommended) 182 'a' min. 100 1010 696 168 'a' 300 min. (600 recommended) min. 100 964 664 170 'a' 300 min. (600 recommended) SP520 'X' 'X' a d c b A B C D E SP420 480 240 566 558 1158 SP520 840 280 554 546 1146 SP920 480 240 566 558 1158 A B MAN AUTO ON OFF S4 S3 S2 S1 ON OFF S3 S2 S1 SP520 SP420 SP920 SP420 SP520 & SP920 7 8 9 10 a b a b 11 12 10a SP520 SP420 SP920 X Y A B C SP520 & SP920 Wall Fires Models: SP420, SP520 & SP920 IMPORTANT: THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RE

The heater should not be connected until the instruction leaflet is read fully. Recessed Installation Please note that this appliance can also be wall-mounted so that it is recessed. This can be installed in a large fireplace opening or a purpose built wall. See Table 1 for size of recess required and hole fixing dimensions and Fig. 5a. This fireplace insert does NOT require venting. In order to ensure it’s future safety in use, it is essential that this fire is securely fixed to the wall. IT IS

7. Manual Operation - SP520 The switches are located at the bottom right side of the heater -see Fig. 6. Remote Operation The standby switch (S1) must first be turned ‘ON’ (and the ‘AUTO/MAN’ Switch turned to ‘AUTO’ - SP420 & SP920). Note: It takes some time for the receiver to respond to the transmitter. DO NOT PRESS the buttons more than once within two seconds for correct operation. Manual & Remote Operation Setting Operation Setting Flame Effect only Press the ‘ I ’ button (Switch 3) Top Neo

FOR YOUR SAFETY Do not store or use gasoline or other fl ammable vapors and liquids in the vicinity of this or any other appliance. FOR YOUR SAFETY WHAT TO DO IF YOU SMELL GAS • Do not try to light any appliance. • Do not touch any electrical switch. • Do not use any phone in your building. • Immediatly call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions. • If you cannot reach your gas supplier, call the fi re department. This appliance may be installed in an a

7. Twist-lock the vent cap onto the kast section of vent pipe. Note: If the vent pipe passes through any occupied areas above the first floor, including storage spaces and closets, you must enclose pipe. You may frame and sheetrock the enclosure with standard construction material. Make sure and meet the minimum allowable clearances to combustibles. Do not fill any of the required air spaces with insulation. If area above is a room, install If the area above is not a room, install firestop above

WARNING: This appliance, when installed must be electrically grounded in accordance with local code or in the absence of local code, with the current National Electric Code, ANSI/NFPA 70, or the Canadian Electric Code, CSA C22.1. Figure 32 - Relocating Junction Box Receptacle and Electrical Supply Connection A pre-wired junction box receptacle with strain relief is provided on the right side of the cabinet for hard wiring the unit to a 15 Amp, 120VAC, 60Hz grounded branch circuit. If the install

(7.6 cm) 9" Min. (22.8 cm) 12" Min. (30.4 cm) 33° 6" Nom. (15.2 cm) 1 1/2" Max. (3.8 cm) Drywall2" X 4" StudCombustibleMaterials Figure 9 - Hearth Extensions Noncombustible Hearth Extension 8" Max. “K” Factor.841 1/2" Typ. 1 1/2" Typ. “Z” Type Ember Protector Figure 11 - Mantel Clearances to Combustible Materials Noncombustible Hearth Extension Seal Gaps withNoncombustibleMortar or AdhesiveTop View of FireplaceDrywall4" (Approx.) (10.1 cm)33° Nom. 6" Nom. (15.2 cm) 4 3/8" Min. (11.1 cm) Combusti

115603-01A OUTSIDE AIR KIT INSTALLATION GAS LINE INSTALLATION 7 OUTSIDE AIR KIT INSTALLATION The installation of the outside air kit must be installed during the rough framing of the fireplace due to the nature of its location. Outside combustion air can be accessed through an exterior wall or a vented crawl space (see Figure 13). CAUTION: Air inlet ducts must not terminate in attic space. The maximum height for the air inlet above the platform of fireplace is a minimum of 3 feet below the chimn

In addition to instructing you on how to install and maintain your appliance, it also contains information that will enable you to obtain replacement parts or accessory items when needed. Keep it with your other important papers. Thisfireboxisapprovedforuseasawoodburningfirebox or for use with a vented gas log approved to ANS Z21.60, Z21.84 or RGA 2-72 standards or for use with a vent-free gas log heater approved to ANS Z21.11.2 standard. This wood burning firebox complies with UL127-CAN/ULSS610

6' Max. Ceiling Support Pipe 12S-8DM Return Elbow 6' Max. 6' Max. Offset Elbow Offset Elbow Return Elbow 6' Max. 6' Max. Offset Elbow C A B Figure 9 - Typical Offset Installation Venting Installation Continued See Detail A Ceiling Support Pipe 12S-8DM 2" Min. See Detail B Straps Straps Straps Straps Detail A Return Elbow Detail B Angle Firestop Figure 10 - Ceiling Support Pipe 12S-8DM OFFSET RISE CHIMNEY LENGTH A B 48" 36" 24" 18" 12" 4 3/8" 16 3/8" ELBOW SET ONLY 9 3/4" 25 1/2" 1 12 3/4" 30 3/4