Power cord sets for use in other countries must meet the requirements of the country where the computer is used. For more information on power cord set requirements, contact a Compaq authorized reseller or service provider. General Requirements The requirements listed below are applicable to all countries: ¦ The length of the power cord set must be at least 5.00 feet (1.5 m) and a maximum of 6.50 feet (2.0 m). ¦ All power cord sets must be approved by an acceptable accredited agency responsible for evaluation in the country where the power cord set will be used. ¦ The power cord set must have a minimum current capacity of 10 amps and a nominal voltage rating of 125 or 250 volts AC, as required by each country’s power system. ¦ The appliance coupler must meet the mechanical configuration of an EN 60 320/IEC 320 Standard Sheet C13 connector, for mating with the appliance inlet on the back of the computer. Maintenance and Service Guide B–1 Power Cord Set Requirements Country-Specific Requirements 3-Conductor Power Cord Set Requirements Country Accredited Agency Applicable Note Number Australia EANSW 1 Austria OVE 1 Belgium CEBC 1 Canada CSA 2 Denmark DEMKO 1 Finland FIMKO 1 France UTE 1 Germany VDE 1 Italy IMQ 1 Japan METI 3 The Netherlands KEMA 1 Norway NEMKO 1 Sweden SEMKO 1 Switzerland SEV 1 United Kingdom BSI 1 United States UL 2 B–2 Maintenance and Service Guide Power Cord Set Requirements Notes 1. The flexible cord must be Type HO5VV-F, 3-conductor, 1.0 mm2 conductor size. Power cord set fittings (appliance coupler and wall plug) must bear the certification mark of the agency responsible for evaluation in the country where it will be used. 2. The flexible cord must be Type SPT-3 or equivalent, No. 18 AWG, 3-conductor. The wall plug must be a two-pole grounding type with a NEMA 5-15P (15 A, 125 V) or NEMA 6-15P (15 A, 250 V) configuration. 3. The appliance coupler, flexible cord, and wall plug must bear a “T” mark and registration number in accordance with the Japanese Dentori Law. The flexible cord must be Type VCT or VCTF, 3-conductor, 1.00 mm2 conductor size. The wall plug must be a two-pole grounding type with a Japanese Industrial Standard C8303 (7 A, 125 V) configuration. Maintenance and Service Guide B–3 C Screw Listing This appendix provides specification and reference information for the screws used in the computer. All screws listed in this appendix are available in the Miscellaneous Screw Kit, spare part number 285290-001. Maintenance and Service Guide C–1 Screw Listing Table C-1 Phillips M3.0 . 4.0 Screw Color Qty. Length Thread Head Width Black 3 4.0 mm 3.0 mm 5.0 mm Where used: One screw that secures the hard drive to the computer (documented in Section 5.3) Figure C-1. Phillips M3.0 . 4.0 Screw Location C–2 Maintenance and Service Guide Screw Listing Ta b l e C -1 Phillips M3.0 . 4.0 Scre w (Continued) Color Q ty . L ength Thread Head Width Black 3 4.0 mm 3.0 mm 5.0 mm Where used: Two screws that secure the hard drive bezel to the hard drive (documented in Section 5.3) Figure C-2. Phillips M3.0 . 4.0 Screw Locations Maintenance and Service Guide C–3 Screw Listing Table C-2 Phillips M2.0 . 5.5 Screw Head Color Qty. Length Thread Width Silver 2 5.5 mm 2.0 mm 4.0 mm Where used: Two screws that secure the connector cover to the computer (documented in Section 5.7) Figure C-3. Phillips M2.0 . 5.5 Screw Locations C–4 Maintenance and Service Guide Screw Listing Table C-2 Phillips M2.0 . 5.5 Screw (Continued) Head Color Qty. Length Thread Width Black 2 5.5 mm 2.0 mm 4.0 mm Where used: Two screws that secure the system board to the base enclosure on each side of the MultiBay connector (documented in Section 5.18) Figure C-4. Phillips M2.0 . 5.5 Screw Locations Maintenance and Service Guide C–5 Screw Listing Table C-3 Phillips M2.0 . 10.0 Screw Color Qty. Length Thread Head Width Black 4 10.0 mm 2.0 mm 4.0 mm Where used: Two screws that secure the LED cover to the computer (documented in Section 5.8) Figure C-5. Phillips M2.0 . 10.0 Screw Locations C–6 Maintenance and Service Guide Screw Listing Table C-3 Phillips M2.0 . 10.0 Screw (Continued) Head Color Qty. Length Thread Width Black 4 10.0 mm 2.0 mm 4.0 mm Where used: Two screws that secure the display hinge covers and display assembly to the computer (documented in Section 5.10) Figure C-6. Phillips M2.0 . 10.0 Screw Locations Maintenance and Service Guide C–7 Screw Listing Table C-4 Phillips M2.0 . 4.0 Screw Head Color Qty. Length Thread Width Gold 13 4.0 mm 2.0 mm 4.0 mm Where used: Two screws that secure the keyboard shield to the computer (documented in Section 5.9) Figure C-7. Phillips M2.0 . 4.0 Screw Locations C–8 Maintenance and Service Guide Screw Listing Table C-4 Phillips M2.0 . 4.0 Screw (Continued) Head Color Qty. Length Thread Width Gold 13 4.0 mm 2.0 mm 4.0 mm Where used: One screw that secures the top cover to the base enclosure in the hard drive bay (documented in Section 5.11) Figure C-8. Phillips M2.0 . 4.0 Screw Locations...
)
