Évaluations - 0, GPA: 0
(
)
)
|
Par ce dispositif a également d'autres instructions :
Facilité d'utilisation
Solution Quick Start Guide | HP Graphics Server Blade XenServer GPU Pass-through Quick Start
XenMotion, Storage XenMotion or VM Suspend not supported at this time
VM’s can be migrated and started on any server with compatible GPU configuration
CUDA, OPenCL supported
Tips and tricks
Prior to XenServer 6.5, in order to set more than two cores per socket (allowing for 4 cores or more) on a virtual
machine, you had to configure the virtual machine through the command-line interface. Use the following command
for XenServer console to enable up to 4 cores per socket and set the virtual machine to use 4 cores at next boot.
xe vm-param-set uuid=
When connecting to a Citrix GPU pass-through session in seamless mode using an end-client display configuration
that is not supported or that the client cannot configure, the session will look like it’s doing something for a few
seconds and then disappear with nothing happening.
WS460c Gen8 systems may lose their network configuration or console screens may turn blank after installing Citrix
XenServer 6.1 Hotfix XS61E030 or installing or upgrading to Citrix XenServer 6.2 if not at system BIOS version
9/20/2013 or newer. Please see the following document for more information:
http://h20564.www2.hp.com/portal/site/hpsc/public/kb/docDisplay/?docId=emr_na-c04013759
On WS460c Gen8, XenServer 6.2 (before SP1), virtual machines (VMs) with NVIDIA GPUs passed-through that do not
have any NVIDIA GPU drivers installed can cause the XenServer RDP console to get locked at 640 by 480 resolution
and 16-bit color mode. Hotfix XS62E010 fixes this issue. Please see the following document for more information:
http://support.citrix.com/article/CTX139643
Setting up XenServer and HDX 3D Pro for pass-through GPU
Configuration steps for XenDesktop 7 and XenServer 6.2
1. Update the WS460c Graphics Server Blade with the latest HP SPP firmware by booting to the SPP DVD.
You can obtain the latest SPP from the following page: http://www.hp.com/go/spp
2. Set up the system BIOS for installation
a. WS460c Gen9
i. Set video mode
1. Connect to the blade using either the iLO remote console or a local SUV connector.
2. When prompted during boot, press the F9 key.
3. Select System Configuration and press ENTER
4. Select BIOS/Platform Configuration and press ENTER
5. Go to and select System Default Options Restore Default Options and press ENTER.
6. System will reset
7. Connect to the blade using either the iLO remote console or a local SUV connector.
8. When prompted during boot, press the F9 key.
9. Select System Configuration and press ENTER
10. Select BIOS/Platform Configuration and press ENTER
11. Select Advanced Options and press ENTER
12. Select Video options and press ENTER
13. choose Both Add-in and Embedded Video Enabled
ii. Set the blade to static high performance mode
1. From BIOS configuration
2. Select Power Management
3. For Power Profile, select Maximum Performance
b. WS460c Gen8
i. Boot to the HP RBSU (BIOS configuration utility) by pressing F9 during boot.
ii. Go to and select System Default Options Restore Default Options and press ENTER.
iii. System will reset
iv. Boot to the HP RBSU (BIOS configuration utility) by pressing F9 during boot.
v. Set the video mode to Setup.
1. Select System Options.
3
...
Ordinateurs - HP ProLiant WS460c Gen9 Configure-to-order Graphics Server Blade (511.1 kb)
Ordinateurs - HP ProLiant WS460c Gen9 Workstation (511.1 kb)