|
Facilité d'utilisation
Keep unit as far away as possible from obstacles and obstructions and at least 30" above the floor or ground. Curtains and other objects within a room should be prevented from blocking the air flow. Window opening requirements (see table below) Awning Side obstruction Ground Fence, wall, or other obstacle. 12" Min. 30" Min. 20" Min. 20" Min. Fig.B ModelSize 8K-10K 12K 15-24K Cabinet size (W*H*D) 20.5" *14.8" *23.1" 22.8" *15.7" *24.1" 26.5" *18.5" *26.9" Min. Window opening 24" 27" 30" Max. Window opening 38" 41" 44" 8 2. Preparation to Remove the Air Conditioner Slide-Out Chassis A. Remove total of (4) Philips screws securing the chassis to the cabinet. There are (2) screws on each side. The set of screws closest to the front of the unit secure the front panel to the cabinet. The set of screw closest to the rear of the unit secure the cabinet to the chassis. See (Fig. 1). B. Remove the front panel assembly from the cabinet by gently pulling it. C. Grasp the pull handle at the front of the slide-out chassis and carefully slide the air conditioner out of the cabinet. See (Fig. 2). Note: Screws must be reinstalled upon completion of the window installation to secure slide-out chassis. Please seek assistance for this procedure. Fig. 2 Fig. 1 Right side Philips screws Shutter Frame Right Shutter 1/4" screw For 8K to 12K models Channel 1/4" Screw Fig. 3 Fig. 4 3. Assembly of the upper & lower channels to the cabinet A. " L" Shaped Top Channel: Stick the double adhering seal to the " L" shaped top channel, and then Install the "L" shaped top channel to the cabinet as shown in (Fig. 3) using (5) 1/4" screws. B. "n" Shaped Bottom Channel installed as shown in (Fig. 3)using (4) 1/4" screws. NOTE: For 15K to 24K models, the bottom channel has been factory- installed, and their shapes may differ from the others,but their functions are similar. 4. Assembly of the side shutters (curtains) to the cabinet. Slide the shutters into the top and bottom channels as shown in (Fig. 4). The shutters are identified (on each frame) as "left" & "right". Attach the shutters to the cabinet using (4) 1/4" screws on each side. Double Adhering seal For 15K to 24K models (Factory-installed). F HR FAN SPEED MODEOFFON/ TIMER Airconditioner WAIT THREE MINUTES BEFORE RESTARTING Coil Pull Handle Chassis 9 INSTALLATION INSTRUCTIONS WAC 8-24 USER MAN FINAL 3/2/05 12:13 PM Page 11 WAC 8-24 USER MAN FINAL 3/2/05 12:13 PM Page 12 INSTALLATION INSTRUCTIONS 5. Installation of Mounting Brackets and First Sealing Strip V-slot NOTE: Windows come in a variety of different styles. Therefore, it may be necessary to modify or improve your particular installation. A. Attach the bracket assembly to 90 angle support brackets (Fig. 5) using (2) 1 1/2" bolts Two bolts per bracket. Secure with the (2) 1/4" lock washers and (2) 1/4"nuts. DO NOT immediately tighten these bolts as it may be necessary to adjust the depth of the bracket assembly, depending on the depth of your window sill. See (Fig. 7).Inst...
Ce manuel est également adapté pour les modèles :Climatiseurs - AAW-08CM1FHUE (5.16 mb)
Climatiseurs - AAW-22CR1FHUE (5.16 mb)
Climatiseurs - AAW-24CM1FHUE (5.16 mb)
Climatiseurs - AAW-08CM1FHUE (5.16 mb)