Log:
Évaluations - 3, GPA: 4 ( )

Instructions Carrier, Modèle AAW-15CM1FHUE

Fabricant : Carrier
Taille : 5.16 mb
Nom Fichier :
Langue d'enseignement: enes
Aller à la télécharger



Facilité d'utilisation


Inadequate support on control side of the unit can result in personal injury and damage to your unit and property. Therefore, it is recommended to have someone assist you during the installation of this unit. E. Be certain the proper electrical outlet is within reach of the installation. Use only a single outlet circuit rated at proper current (see table 1 on page 4). All wiring should be in accordance with local and national electrical codes. F. Your unit was designed to evaporate condensation under normal conditions. However, under extreme humidity conditions, excess condensation may cause the basepan to overflow to the outside. The unit should be installed where condensation run-off cannot drip on pedestrians or neighboring properties. 1. Select the Best Location A. Your room air conditioner was designed to fit easily into a single or double hung window. However, since window designs vary, it may be necessary to make some modifications for safe and proper installation. B. Make sure window and frame is structurally sound and free from dry and rotted wood. C. For maximum efficiency, install the air conditioner on side of the house or building which favors more shade than sunlight. If the unit is in direct sunlight, it is advisable to provide an awning over the unit. D. Provide sufficient clearance around the cabinet to allow for ample air circulation through the unit. See (Fig.B). The rear of the unit should be outdoors and not in a garage nor inside of a building. Keep unit as far away as possible from obstacles and obstructions and at least 30" above the floor or ground. Curtains and other objects within a room should be prevented from blocking the air flow. Window opening requirements (see table below) Awning Side obstruction Ground Fence, wall, or other obstacle. 12" Min. 30" Min. 20" Min. 20" Min. Fig.B ModelSize 8K-10K 12K 15-24K Cabinet size (W*H*D) 20.5" *14.8" *23.1" 22.8" *15.7" *24.1" 26.5" *18.5" *26.9" Min. Window opening 24" 27" 30" Max. Window opening 38" 41" 44" 8 2. Preparation to Remove the Air Conditioner Slide-Out Chassis A. Remove total of (4) Philips screws securing the chassis to the cabinet. There are (2) screws on each side. The set of screws closest to the front of the unit secure the front panel to the cabinet. The set of screw closest to the rear of the unit secure the cabinet to the chassis. See (Fig. 1). B. Remove the front panel assembly from the cabinet by gently pulling it. C. Grasp the pull handle at the front of the slide-out chassis and carefully slide the air conditioner out of the cabinet. See (Fig. 2). Note: Screws must be reinstalled upon completion of the window installation to secure slide-out chassis. Please seek assistance for this procedure. Fig. 2 Fig. 1 Right side Philips screws Shutter Frame Right Shutter 1/4" screw For 8K to 12K models Channel 1/4" Screw Fig. 3 Fig. 4 3. Assembly of the upper & lower channels to the cabinet A. " L" Shaped Top Channel: Stick the double adhering seal to the " L" sha...

Ce manuel est également adapté pour les modèles :
Climatiseurs - AAW-08CM1FHUE (5.16 mb)
Climatiseurs - AAW-22CR1FHUE (5.16 mb)
Climatiseurs - AAW-24CM1FHUE (5.16 mb)
Climatiseurs - AAW-24CR1FHUE (5.16 mb)

Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories