Évaluations - 2, GPA: 3 ( )

Fabricant : Heat Controller Taille : 554.77 kb Nom Fichier : Langue d'enseignement:

6 M). Each time the button is pressed, the fan speed changes in the following order: AUTO HIGH MED LOW QUIET About three seconds later, the entire display will reappear. When set to AUTO: Heating : Fan operates so as to optimally circulate warmed air. However, the fan will operate at very low speed when the temperature of the air issued from the indoor unit is low. Cooling : As the room temperature approaches that of the thermostat setting, the fan speed becomes slower. Fan : The fan runs at the low fan speed. The fan will operate at a very low setting during Monitor operation and at the start of the Heating mode. SUPER QUIET Operation SUPER QUIET operation begins. The indoor unit’s airflow will be reduced for quieter operation. SUPER QUIET operation cannot be used during Dry mode. (The same is true when dry mode is selected during AUTO mode operation.) During Super Quiet operation, Heating and Cooling performance will be reduced somewhat. If the room does not warm up/ cool down when using SUPER QUIET Operation, please adjust the air conditioner’s Fan Speed. OPERATION s s s s Example: When set to COOL. Example: When set to 80 °F. Example: When set to AUTO. s s s s t t En-6 To Stop Operation Press the START/STOP button (Fig.6 N). The OPERATION Indicator Lamp (red) (Fig. 3 5) will go out. About AUTO CHANGEOVER Operation AUTO: When AUTO CHANGEOVER operation first selected, the fan will operate at very low speed for about one minute, during which time the unit detects the room conditions and selects the proper operating mode. If the differance between thermostat setting and actual room temperature is more than +4 °F > Cooling or dry operation If the difference between thermostat setting and actual room temperature is within ±4 °F > Monitor operation If the difference between thermostat setting and actual room temperature is more than –4 °F > Heating operation When the air conditioner has adjusted your room’s temperature to near the thermostat setting, it will begin monitor operation. In the monitor operation mode, the fan will operate at low speed. If the room temperature subsequently changes, the air conditioner will once again select the appropriate operation (Heating, Cooling) to adjust the temperature to the value set in the thermostat. (The monitor operation range is ±4 °F relative to the thermostat setting.) If the mode automatically selected by the unit is not what you wish, select one of the mode operation (HEAT, COOL, DRY, FAN). About Mode Operation Heating: Use to warm your room. When Heating mode is selected, the air conditioner will operate at very low fan speed for about 3 to 5 minutes, after which it will switch to the selected fan setting. This period of time is provided to allow the indoor unit to warm up before begin full operation. When the room temperature is very low, frost may form on the outside unit, and its performance may be reduced. In order to remove such frost, the unit will automatically enter the defrost cycle from time to time. During Automatic Defrosting operation, the OPERATION Indicator Lamp (red) (Fig. 3 5)will flash, and the heat operation will be interrupted. Cooling: Use to cool your room. Dry: Use for gently cooling while dehumidifying your room. You cannot heat the room during Dry mode. During Dry mode, the unit will operate at low speed; in order to adjust room humidity, the indoor unit’s fan may stop from time to time. Also, the fan may operate at very low speed when adjusting room humidity. The fan speed cannot be changed manually when Dry mode has been selected. Fan: Use to circulate the air throughout your room. During Heating mode: Set the thermostat to a temperature setting that is higher than the current room temperature. The Heating mode will not operate if the thermostat is set lower than the actual room temperature. During Cooling/Dry mode: Set the thermostat to a temperature setting that is lower than the current room temperature. The Cooling and Dry modes will not operate if the thermostat is set higher than the actual room temperature (in Cooling mode, the fan alone will operate). During Fan mode: You can not use the unit to heat and cool your room. En-7 2 Press the AIR CLEAN button (Fig. 6 O). The AIR CLEAN Indicator Lamp (green) (Fig. 3 7) will light up. Air conditioning and Air Cleaning will function simultaneously. Air cleaning During operation, the unit produces a small amount of ozone that can be smelled. When this unit is used in combination with the ultrasonic humidifier, white particles may become attached to the plasma filter unit. If this happens, clean the plasma filter unit as soon as possible. (Refer to page 13, 14.) The air cleaning operation cannot remove gases such as carbon monoxide and alcohol from the air. During operation, ventilate the room often to prevent asphyxiation or suffocation. If the intake filter is removed during operation, a safety device will stop the operation of the plasma filter unit. If this happens, ...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :