Cisco CRS Carrier Routing System 8-Slot Line Card Chassis Site Planning Guide CONTENTS Preface v CHAPTER 1 Cisco CRS Carrier Routing System 1-1 The Cisco CRS 8-Slot Line Card Chassis 1-2 Chassis Components 1-7 Chassis Slot Numbers 1-9 Overview of Site Planning Steps 1-11 CHAPTER 2 Power and Cooling 2-1 Chassis Power System 2-1 General Power and Grounding Requirements 2-2 Bonding and Grounding Guidelines 2-3 DC Power Systems 2-5 Fixed Configuration DC Power Requirements 2-5 Fixed Configuration DC

USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS. THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY. The following information is for FCC compliance of Class A devices: This equipment has been tested and found to comply wi

Refer to the following documentation for installation and replacement of parts (including shared port adapters) and regulatory compliance information: • Shared port adapter documentation—See the Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide • Configuration documentation—See the Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide Document Revision History The Document Revision History table below records technical changes to

A foundation of the Intelligent Information Network, Cisco routers provide high availability, comprehensive security, integrated wireless, ease of management, and advanced quality of service (QoS) for today’s most demanding network services, including IP communications, video, customer relationship management, financial transactions, and other real-time applications. This guide shows how Cisco Services Aggregation Routers and Cisco Integrated Services Routers enable you to meet your current and

The Catalyst 6500 Series delivers scalable, secure, converged, L2 and L3 services, from the data center and campus to the WAN aggregation and the Internet edge. Delivering scalable performance and port density with investment protection across several chassis configurations and LAN, WAN, and MAN interfaces, the Catalyst 6500 Series switches feature an unparalleled range of integrated services modules, including multi-gigabit network security, content switching, telephony, and network analysis mo

3. This length is specifically between any two stations on a repeated segment. Table 5 lists IEEE 802.3u physical characteristics for 100BASE-TX. Table 5 IEEE 802.3u Physical Characteristics Parameter 100BASE-TX Data rate (Mbps) 100 Signaling method Baseband Maximum segment length 100 m between DTE1 and repeaters Media Category 5 UTP (for RJ-45) Topology Star/Hub 1. DTE = data terminal equipment. OL-11656-01 Performance Route Processor Installation and Configuration Guide 47 Configuring Interfac

After some interface information displays, the prompt appears as follows: Router> Step 10 Enter the enable command to enter enabled mode. The prompt changes to the following: Router# Step 11 Enter the show start-up config EXEC command to display the enable password in the configuration file. Step 12 Enter the configure terminal command at the EXEC prompt. You are prompted as follows: Router# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Router(config)# Change th

System power is turned on. 2. MBus module receives +5 VDC and starts executing MBus software. 3. PRP determines the system configuration by sending a message over the MBus requesting all installed devices to identify themselves. The return response provides slot number, and card and component type. The PRP, line cards, and clock scheduler cards (CSCs) are then powered up. 4. PRP power-on-reset logic delay, which allows power and both local and CSC clocks to stabilize. 5. After the power-on reset

All rights reserved. Important Information • Upgrading Chopper FPGA on PRP-2, page 80 • Regulatory, Compliance, and Safety Information, page 83 • Obtaining Documentation, page 88 Important Information This section contains information about the following hardware and software requirements: • Router Information, page 2 • Cisco IOS Software Requirements, page 3 • Hardware Revision Requirements, page 4 • Related Documentation, page 5 Router Information For hardware installation and maintenance info

(See Figure A-6.) SLOT-0 SLOT-1 RESET AUX CONSOLE EJECT ACTIVE 0 CARRIER RX CELL ACTIVE CARRIER RX PKT DOWN LOOP RA LA CDHNT CD TX 0 RX TX 1 RX TX 2 RX TX 3 RX TX 4 RX TX 5 RX TX 6 RX DOWN LOOP RA LA CDHNT CD TX 0 RX TX 1 RX TX 2 RX TX 3 RX TX 4 RX TX 5 RX ACTIVE 0 CARRIER RX PKT ACTIVE 1 CARRIER RX PKT ACTIVE 2 CARRIER ACO/LT CRITICAL MAJOR MINOR Front of chassis 29188 A-15 Cisco XR 12416 and Cisco XR 12816 Router Chassis Installation Guide OL-17440-01 Appendix A Repackaging the Router Repackag