Évaluations - 2, GPA: 5
(
)
)
|
Facilité d'utilisation
6 and serrated flange nuts (D). PLACiNG SAW AND EXTENSioN TABLE oN MoBiLE BASE RiSK oF iNJURY FRoM LiFTiNG. Serious injury can result from attempting to lift too heavy an object. The machine can weigh more than 550 pounds and is too heavy to be lifted by one person. Obtain assistance from others before lifting. PiNCH HAZARD. Be sure not to place toes or fingers underneath the base of the Unisaw while moving. Lift the saw from underneath the table, before saw is assembled, or from underneath the wings and extension table after assembly. Carefully lift saw and extension table onto mobile base. Make sure extension legs (EE) Fig. 7 rest on angle brackets (I) as shown. ASSEMBLiNG J BoLTS To ANGLE BRACKETS The J bolts are required to join the base to the extension table legs and will keep the table legs resting properly on the base while moving the base. 1. Place 1/4-20 hex nut (S) Fig. 7 on J-bolt (P) and screw it on until it bottoms out on threads. 2. Make sure J bolt (P) Fig. 7 is around leveling screw (GG) on extension leg (EE) as shown in Fig. 7. 3. Insert J bolt (P) Fig. 1 and Fig. 7 through hole (FF) Fig. 3 in angle bracket (I). 4. Adjust hex nut (S) until it touches the angle bracket (I). 5. Place a 1/4" flat washer (Q) Fig. 7 on J bolt (P) and fasten it to angle bracket (I) using a 1/4-20 Nylon lock nut (R). Tighten nut using 7/16" wrench. 6. Repeat for J bolt (P) on the other angle bracket (I). oPERATiNG MoBiLE BASE NoTE: Before operating the base, apply grease to the cams (HH) Fig. 8 and where they meet the foot pedal bracket (AA). When the foot pedal (II) is pushed down as shown in Figure 9, the base is mobile. To reduce the risk of injury, do not operate the saw when the base is mobile (when the foot pedal (ii) is pushed down as shown in Fig. 9). When the foot pedal (II) is raised (as shown in Figure 10), the base is lowered down to the floor so it does not move. If the saw is not level in this position, you can adjust the two extension table legs (EE) Fig. 7 on your Unisaw using the leveling screw (GG). To reduce the risk of injury, when lifting on foot pedal (II) Fig. 9 to lower the saw down and make it stationary, be careful as the pedal swings back with force. Stay clear of the motion of this pedal. To reduce the risk of injury, make sure that your feet are clear of the base before lowering the unit. Figure 11 shows a Unisaw correctly attached to the mobile base. II FIG. 9 FIG. 10 II C H Q P R D E G I L M N O T FIG. 1 S A B F J K FIG. 5 Y Z AA C F D G FIG. 2 M K O N L U K V FIG. 7 EE R Q P GGP S WX I J A FIG. 3 FIG. 4 I B E H CC BB DFIG. 6 CT DD FF HH HH AA FIG. 8 FIG. 11 BASE MoBiLE DE SCiE UNiSAW DELTA 50-257 ou 50-2000 PoUR ToUT CoMMENTAiRE, oU QUESTioN, RELATiF A CET ACCESSoiRE oU ToUT AUTRE ACCESSoiRE DELTA, CoMPoSER GRATUiTEMENT LE : 800223- 7278. CoNSiGNES DE SECURiTE Pour reduire tout risque de dommages corporels, lire le manuel de l’utilisateur respectif a l’outil avant l’utilisation de tout accessoire. Tout manquement a ces avertissements augmente les risques de blessures, et les risques de serieusement endommager l’appareil et ses accessoires. Lors de l’entretien de cet outil, n’utiliser que des pieces de rechange identiques. Pour reduire tout risque de dommages corporels, arreter et debrancher l’outil du secteur avant d’installer ou retirer tout accessoire, avant tout reglage ou pour faire toute reparation. Tout demarrage accidentel comporte des risques de dommages corporels. les bases mobiles, 50-257 et 50-2000, ont ete testees et approuvees pour etre utilisees seulement avec les scies Unisaw DELTA inclinables a gauche, construites a partir de mars 2009. La date codee de fabrication est indiquee sur la scie Unisaw sous le format : 2009 x-39. (Le « x » represente la semaine de l’annee de fabrication.) CoNTENU DU CARToN (FiG. 1) A. (2) Pieds en caoutchouc B. (2) Ecrous hexagonaux de 1/2-13 C. (1) Dispositif pedale D. (7) Ecrous freines hexagonaux a collet dentele de 3/8-16 E. (3) Boulons a tete bombee de 76,2 mm (3/8-16 x 3 po) F. (4) Vis a tete hexagonale de 19 mm (3/8-16 x 3/4 po) G. (1) Roulette pivotante de 76,2 mm (3 po) H. (1) Support pivotant I. (2) Cornieres d’assemblage de pied J. (4) Boulons freines hexagonaux a collet dentele de 19 mm (5/16-18 x 3/4 po) K. (2) Roues L. (2) Vis de 50,8 mm (2 po) a epaulement de 9,5 mm (3/8 po) ; filetage de 5/16-18 po M. (2) Manchons de vis a epaulement N. (2) Rondelles plates de 5/16 po O. (2) Contre-ecrous de nylon de 5/16-20 P. (2) Boulons a «J» de 1/4-20 x 58,7 mm (2-5/16 po) Q. (2) Rondelles plates de 1/4 po R. (2) Contre-ecrous de nylon de 1/4-20 S. (2) Ecrous hexagonaux de 1/4-20 T. Cadre de base de scie iNTRoDUCTioN Cette base mobile presente : supports d’acier corroye renforce, levier a pied boulonne, roulette pivotante unique, et deu...
Ce manuel est également adapté pour les modèles :Jig Saw et - 50-2000 (1.35 mb)