Box 168 803-271-9000 Myrtle Beach 29577 Coastal Elec. & Rewinding 718 8th Avenue N. 803-448-3586 Spartanburg 29302 Cash Supply 113 Country Club Rd 803-585-9326 SOUTH DAKOTA Rapid City 57702 Stan Houston Equipment Co. 1210 Deadwood Avenue 605-348-1155 Sioux Falls 57702 Sian Houston Equip. Co 501 S Marrion Road 605-336-3727 TENNESSEE Chattanooga 37412 F & D Tool Service and Supply 4121 Ringgold Road 615-698-6454 Clarksville 37042 Opa's Shop 312 Pine Mountain Road 615-647-5842 Jackso

If an adapter is used to accommodate a two-prong receptacle, the adapter wire must be attached to a known .pound. Never remove the third prong. 4. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to ж that keys and adjusting wrenches are removed before turning on tool. 5. KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents. 6. AVOID DANGEROUS ENVIRONMENT. Don't expose power tools to rain. Don't use power tools in damp or wet locations. Keep your work area well Illumi

If the end of the rod strikes the table do not change the height adjustment of the saw. Instead, lower the front right side of the table by turning the upper nut on the suspension stud up a few turns. You should now be able to push the front right corner of the table down so the rod indicator can pass over the surface without striking it. 7. Adjust the suspension stud nuts so the top of the table on the front right side just touches the end of the antikickback rod the same as the back. Tighten

Replace cover by lining up holes in cover with holes in the raised sections of the ball retainer assembly. Replace screws and tighten securely (Fig. A13). Fig. A13 2. YOKE CLAMP HANDLE The purpose of this handle is to provide a friction lock between the -upper face of the yoke and the bottom face of the rollerhead. It should also eliminate any play between these two ■ parts. To lock, the handle is 'pushed back from the hand grip of the yoke. If at any time if is possible to move this handle s

Turn the motor “OFF”. Figure K5C Moving the saw back through lb« trough and 1/4-circle kerfs, bring the saw again to the position at the-end of the arm as shown in Figure K5. Tighten Rip Lock and release Yoke Clamp Handle. Turn -motor “ON" and temporarily press the Yoke Locator Pin Handle as you start to rotate the yoke counterclockwise (Figure K5D). Continue rotating until the Locator. Pin stops the yoke, after a 1/4-circie cut, with the blade parallel to the fence. Now, with the motor still

REVIEW SAFETY RULES AND OPERATING INSTRUCTIONS FREQUENTLY. This booklet is provided for your convenience: iw the use ami care of your new DeWalt Saw. These instructions include operation, usage, precautions^ preventive maintenance, maintenance and other pertinent data to assist you in assuring long; life and dependable service from your saw. 700 8" RADIAL ARM SAW No. 7700/3400,120 VOLT, TYPE 5 No. 7700-01,220 VOLT, TYPE 5 Bulletin No. 8814 - INDEX Unpacking, Set-Up..............2-4 Macfii

Set and test the anti-kickback device the same as in RIPPING even though only one of the fingers will take the main “bite”, if needed.-Remember to raise the front, lower blade guard to clear rip fence if needed. Figure §13 20 DADO & PLOUGH CUTS (CUTTING GROOVES) Figure S14 A “Dado” is a grmm mmm the wood grain Ccrosscut) (figure S14). A “Plough" is a groove with the wood grain (rip) (Figure $15). These cuts can be made to any width with a regular saw blade by miking one cut next to another

To calibrate the blade tilt: 1. Disconnect the saw from the power source! 2. Move the blade tilt to 90. according to the gauge, and raise the main blade as high as it will go. 3. Place a machinist's square on the table surface and between the blade teeth. Inspect for gaps between the blade and the square. 4. If a gap exists at either the top or bottom of the square, loosen the set screw in the 90. tilt stop nut shown in Figure 83. 90. Tilt Stop Nut 45. Tilt Stop Nut Leadscrew Nut Figure 83. Blad

G0451 14" Sliding Table Saw -9 Additional Safety Instructions for Table Saws 1. SAFETY ACCESSORIES. Always use the blade guard and riving knife on all ''throughsawing'' operations. Through-sawing operations are those when the blade cuts com7. RIVING KNIFE ALIGNMENT. Only operate the saw if the riving knife is aligned with the main blade. pletely through the workpiece. 8. REACHING OVER SAW BLADE. Never reach behind or over the blade with either 2. 3. KICKBACK. Be familiar with kickback. Kickback

7. Use the clamp assembly (10) to secure the workpiece wherever possible. 8. It is possible to remove the clamp assembly (10) by loosening the clamp assembly lock (11) and moving it to the other side of the table. Make sure the clamp assembly lock is tight before using the clamp (Fig. r). 9. Before turning on the saw, perform a dry run of the cutting operation to check that there are no problems. 10. Hold the operating handle (7) firmly and squeeze the switch trigger (24). Allow the blade to rea