Évaluations - 3, GPA: 3.7
(
)
)
|
Facilité d'utilisation
Replace them with new ones as soon as possible. To Prevent Possible Damage to this Unit •Load new battery with their polarities (© and ©) aligned correctly. •Do not apply heat to batteries, or internal shortcir-cuit may occur. •If this unit is not to be used for a long period of time, or used on AC power source, remove the batteries and store them in a cool and dry place. •Remove spent batteries immediately. •Do not use old and new batteries together. Also never use an alkaline battery with a manganese battery. 1. Connect the included stereo earphones to the Headphones Jack. 2. Set the Function Selector to "FM" or “AM". 3. Tune in your favorite station using the Tuning Control. •When you listen to a FM broadcast, set the FM Mode Selector to the proper position (Refer below). 4. Adjust the Volume Control, Graphic Equalizer Controls and XBS Level Control to the desired setting. •To turn off the radio, set the Function Selector to “TAPE IofpI". Notes: •To receive FM stereo broadcasts, set the FM/Mode Selector to “STEREO". •If FM stereo reception is poor (excessive noise), set the FM Mode Selector to “MONO". This will reduce the noise and provide more clear reception; however, the broadcast will not be heard in stereo. -8- ■ XBS Level Control Set this control to "MAX” during broadcasting or tape playback to boost the low frequency range. You can enjoy dynamic low sound as if you were in a concert hall. ■ Graphic Equalizer It allows you to tailor the frequency response of the unit to compensate for room acoustics and other factors which affect frequency response. The overall tone can be altered by adjusting the controls which control the following frequency bands: 330 Hz, 1 kHz, 10 kHz Positioning the control to the "+” side of the detent will amplify the corresponding frequency band; the side will attenuate it. ■ Antennas FM: The earphones cord serves as the FM antenna, hence be sure to use It extended, not coiled. AM: The sensitive ferrite core antenna inside the set will provide excellent AM reception in most areas. For optimum reception, turn the set in the direction which gives the best results, since the ferrite core antenna is directional. Note: Be sure to have the set in an upright position when you listen to AM broadcasts. If you use the radio in a horizontal position, it may not function adequately. ~ 9 - TAPE PLAYBACK 1. Open the Cassette Compartment Cover with your hand. Insert a cassette as shown in the figure, and then close the Cassette Compartment Cover, (-sa [¥}). 2. Connect the included stereo earphones to the Headphones Jack. 3. Set the Function Selector to "TAPE ¡offI”. 4. Press the Playback Button, and playback will begin. 5. Adjust the Volume Control, XBS Level Control and Graphic Equalizer Controls to the desired settings. •To stop the playback, press the Stop Button. Notes: •Do not open the Cassette Compartment Cover during playback. •If you set the Function Selector to "FM" or "AM" during playback, the Playback Button will not be released although the motor has stopped. Press the Stop Button to release the Playback Button. ■ Fast Forward and Rewind The tape will rapidly advance in the forward or reverse direction when one of the Fast Buttons is pressed. Notes: •When the tape reaches the end by pressing one of the Fast Buttons, the tape movement stops, but the unit is not turned off. Do not leave the set in this condition. Be sure to press the Stop Button. •Do not press the Playback Button during fast forward or rewind, as this may jam the tape. Always press the Stop Button first, between functions. •I -10- ■ Dolby Noise Reduction This unit includes Dolby Noise Reduction which reduces tape noise to a remarkable degree. •Set the Dolby Noise Reduction Switch to "ON” to playback a tape recorded with Dolby Noise Reduction. For other tapes, set the switch to "OFF”. ■ Tape Selector Set the Selector to the appropriate position according to the type of tape being used. CrOz ImtlI: Metal tape/High bias chromium tape or equivalent NOR: Low bias ferric oxide tape ■ Auto Reverse (Continuous Playback) When the tape comes to the end of its travel, the auto reverse system functions, and the tape direction changes automatically to start playing the opposite side of the tape. •The cassette tape will run continuously, changing from forward to reverse, then back again, etc., until the Stop Button is pressed. ■ Manual Reverse Select the playback side, Forward or Reverse, by setting the Direction Selector to “FWD” or “REV". BELT CLIP (‘m [f]) MAINTENANCE (-w[gD •If the head assembly is extremely dirty, clean them with a soft cloth dampened with a little atcohoi. •Do not bring any type of metal objects or tools such as magnetic screwdrivers in contact with the head assembly. •Do not clean the plastic cabinet with benzine or thinner. Clean it with a solution of soap and water. •Avoid spray-type insecticides. Some insecticides contain chemicals tha...