|
Facilité d'utilisation
For best results, extend the FM antenna fully and fix to a wall or door frame. Don’t drape loosely or leave coiled up. Connecting external antennas External AM antenna Use 5–6 meters of vinyl-insulated wire and set up either indoors or outdoors. Leave the AM loop antenna connected. ANTENNA AM LOOP ANTENNA FM UNBAL 75. Outdoor antenna 5–6m Indoor antenna (vinyl-coated wire) External FM antenna Use a PAL connector to hook up an external FM antenna. ANTENNA AM LOOP ANTENNA FM UNBAL 75. PAL connector Connecting to your TV This system offers three types of video connections. If your TV has component video inputs, see Connecting using the component video output below. 1 Use the supplied yellow video cable to connect the VIDEO OUT jack to a video input on your TV. VIDEOOUT For a better image, you can also use a commercially available S-Video cable to connect the S-VIDEO OUT jack to an S-Video input on your TV. S-VIDEOOUT 2 Optionally: Use a stereo audio cable to connect the audio outs of your TV (or VCR) to the LINE IN jacks on the rear of this unit. This will enable you to hear the TV (or VCR) sound through this system. See Connecting auxiliary components below for more on this. English FrancaisDeutsch NederlandsItaliano Espanol Note 1 The signal ground ( ) is designed to reduce noise that occurs when an antenna is connected. It is not an electrical safety ground. 11 En Connecting up Connecting up Connecting using the component video output If your TV has component video inputs, you can use these instead of the standard or S-Video output to connect this system to your TV.1 This should give you the best quality picture from the three types of video output available. • Use a component video cable to connect the COMPONENT VIDEO OUT to a set of component inputs on your TV. COMPONENT VIDEO OUT L R L R CUT LINE VIDEO OUT PR PB S VIDEO OUT IN COMPONENT INPUT About progressive scan video Compared to interlace video, progressive scan video effectively doubles the scanning rate of the picture, resulting in a very stable, flicker- free image. Progressive scan video is available only from the component video output. Important • If you connect a TV that is not compatible with a progressive scan signal and switch the system to progressive, you will not be able to see any picture at all. In this case, press STANDBY/ON to put the system in standby, then press and hold the front panel (stop) button for about 7 seconds until the display shows MEM.CLR?. Press the front panel or button so that the display shows INTERL?. Press the front panel button to set to interlace and switch the system back on. Compatibility of this player with progressive-scan and high-definition TVs. This player is compatible with progressive video Macro Vision System Copy Guard.2 This system is compatible with the following Pioneer displays and monitors: PDP-505HDG, PDP-435HDG, PDP-5040HD, PDP4340HD, PDP-502MX, PDP-503HDG, PDP-504HDG, PDP-433HDG, PDP-434HDG, SD-532HD5, SD533HD5. Connecting auxiliary components This system has both stereo analog inputs and outputs. Use these to connect external components, such as a VCR, MD, CD-R or DAT recorder. • Connect the LINE IN jacks on the rear panel to an auxiliary playback component. These include components such as a VCR, DAT, or your TV. Connect using RCA pin-plug stereo cables. • Connect the LINE OUT jacks on the rear panel to a recording component. These include components such as a cassette deck, VCR, MD recorder, or another recorder with analog inputs. Connect using RCA pin- plug stereo cables. Note 1 The component video output is switchable between interlaced and progressive formats. See Video Output settings on page 44. 2 Consumers should note that not all high-definition television sets are fully compatible with this product and may cause artifacts to be displayed in the picture. In case of 525 progressive scan picture problems, it is recommended that the user switch the connection to the ‘standard definition’ output (Interlace). If there are questions regarding our TV set compatibility with this model, please contact our customer service center. En Connecting up Connecting up 02 Connecting the power After making sure that everything is connected properly, plug in the power cord to the AC inlet, and the other end to a mains power outlet. AC IN Congratulations! You’re done setting up. English FrancaisDeutsch NederlandsItaliano Espanol En Controls and displays Controls and displays Chapter 3 Controls and displays Front panel Illustration shows the EV700/1000 model 1 Display See Display below. 2 Sound options FRONT SURROUND (EV700/1000 only) – Switches on the Front Surround mode (page 26). PHONES SUB MAIN MIC VOL MS+/FF MUSIC TIMER DVD/CD TA P E LINE TUNER VOLUME STANDBY/ON MOVIE FRONT SURROUND SOUND MODE KARAOKE ENTER REVERSE MODE REC/STOP ASES PUSH OPEN +– TUNING MS–/REW MIC MIN MAX 1 4 14 12 13 7 8 9 6 5 10 11 32 SFC (EV500 only) – Selects sound modes or custom settings from the Sound Field Control (...
Ce manuel est également adapté pour les modèles :Récepteurs - S-EV1000V (1.33 mb)
Récepteurs - XV-EV500 (1.33 mb)
Récepteurs - XV-EV700 (1.33 mb)
Récepteurs - S-EV500V (1.33 mb)