Évaluations - 2, GPA: 4.5 ( )

Fabricant : Pioneer Taille : 1.33 mb Nom Fichier : Langue d'enseignement:

Use this setup together with the Front Surround modes to take advantage of wall and ceiling reflections for a very realistic surround effect. Front left Front right Surround left Surround right Listening position Center Subwoofer After placing your speakers, complete Setting the channel levels then refer to Speaker distance setting on the next page to complete your surround sound setup. Setting the channel levels Set the relative channel levels from your main listening position.2 1 Press TEST TONE (SHIFT+7). The test tone is output in the following order (from the speakers active in the current listening mode): • L – Front left speaker • C – Center speaker • R – Front right speaker • RS – Surround right speaker • LS – Surround left speaker • SW – Subwoofer3 2 Use the VOLUME +/– button to adjust the volume to an appropriate level. 3 Use the / buttons to adjust the speaker levels in turn. You should hear the test tone at the same volume from each speaker when seated in the main listening position. The channel level range is ± 10 dB. 4 When you’re done, press TEST TONE to exit test tone setup. Note 1 See About the listening modes on page 25 for more on using the different listening modes with each speaker setup. 2• Make sure headphones are unplugged. • The channel balance can be adjusted (independently for each listening mode) while listening to any sound source you want: Press CH LEVEL (SHIFT+8) then use / to select channels and / to adjust the level. Press ENTER when you’re finished. 3 Since the subwoofer produces ultra-low frequencies its sound may seem quieter than it actually is. En Setting up for surround sound Setting up for surround sound Choosing your surround settings To get the best possible surround sound from your system, make the settings below. You should only need to make these settings once (unless you change the placement of your speakers or wish to change settings for a particular disc). 1 Press SYSTEM SETUP (SHIFT+HOME MENU).1 2 Use / to choose the setting. The current setting is shown for each option as you cycle through the display. See below for a full list and description of each. 3 Use / to adjust. 4 Repeat steps 2 and 3 for other settings. 5 When you’re done, press ENTER to leave the System Setup menu. System Setup menu options Below are all the available settings in the setup menu.2 The first setting in each section is the default. See also the notes in each section for additional information about the settings. Speaker distance setting Specifies the distance from your listening position to your speakers. When DIST.? appears, press ENTER, then use / to adjust the distance, and / to switch between the following speakers: • L – Front left speaker • C – Center speaker • R – Front right speaker • RS – Surround right speaker • LS – Surround left speaker • SW – Subwoofer Each speaker can be adjusted between 0.3m ~ 9m. The default setting is 3m. Dynamic Range Control Specifies dynamic range adjustment to Dolby Digital or DTS soundtracks:3 • DRC OFF – No dynamic range adjustment (use when listening at higher volume) • DRC MID – Mid setting • DRC HIGH – Dynamic range is reduced (loud sounds are reduced in volume while quieter sounds are increased) LFE attenuator setting Dolby Digital and DTS audio sources include ultra-low bass tones. Set the LFE attenuator as needed to prevent the ultra-low bass from distorting the sound. • LFEATT 0 – No attenuation • LFEATT 10 – LFE channel attenuated 10dB • LFE Off – LFE channel is not played Subwoofer setting You can switch between subwoofer settings to provide extra bass or to hear the subwoofer channel ‘as is’. • SW PLUS – This provides extra bass when listening to an audio source • SW AUTO – The subwoofer channel is heard without any additional processing. DTS CD setting If you play a DTS-encoded CD, you will need to change this setting to hear the decoded signal. When CD TYPE? appears, press ENTER, then use / to select the setting: • NORM.CD – Regular CD playback, DTS- encoded CDs may output some noise • DTS-CD – Proper decoding of DTS- encoded CDs, but regular CD playback may lose quality Note 1 These settings can’t be changed when recording, or when the Line Recording feature is on (see Using the Sound menu on page 27). 2 If the tuner is selected, the auto preset feature also appears (see Automatically saving station presets on page 37). 3 This setting works only with Dolby Digital and some DTS soundtracks. En Home theater sound 06 Chapter 6 Home theater sound English FrancaisDeutsch NederlandsItaliano Espanol EV700/1000 model only About the listening modes As explained in Home theater sound setup on page 23, there are two basic surround speaker setup options available. Of course you can select any of the listening modes regardless of how you place your speakers, but you will achieve the best surround effect by using the listening modes in conjunction with your speaker setup: • Standard surround 5-spot setup – Use the Standard (Listening in surround...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :