You must select channels at the Cable Box. 3. Use a second RF OUT IN 75WANT /CABLE ANTENNA IN Jack Back of TV (example only) 1. Connect the Cable signal to the IN Jack on the Cable Box. coaxial cable to con- nect the ANT(enna) OUT jack on the VCP to the TV’s ANTENNA IN Jack. 2. Use the RF coaxial cable (supplied) to connect the OUT Jack on the Cable Box to the ANT(enna) IN Jack on the VCP. Watching TV with the VCP Off 1 Set the TV to the Cable Box output channel (channel 3 or 4). 2 Select the ch

. . . . . . . . . . .27 Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 Basic Operations Playing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 Recording . . . . . . . . . . . . . . . . . . . . . . . . . . .

To change a fuse in this type of plug proceed as follows: 1 Remove fuse cover and fuse. 2 Fix new fuse which should be a BS1362 5 Amp, A.S.T.A. or BSI approved type. 3 Refit the fuse cover. If the fitted plug is not suitable for your socket outlets, it should be cut off and an appropriate plug fitted in its place. If the mains plug contains a fuse, this should have a value of 5 Amp. If a plug without a fuse is used, the fuse at the distribution board should not be greater than 5 Amp. Note:

If – – : – – appears on the display panel after you turn off the VCR, the VCR could not find the time. Use a different method to set the clock. • When the power plug is connected to an AC outlet, the correct time will appear on the display panel of the VCR when the power is off. • Press the EXIT/STATUS button repeatedly to make the time appear on the display panel when the VCR power is on. Helpful Hints 16 Setting the Clock (cont’d) Manual PBS Channel Selection 7 VCRTV VCR/TV QUICK PROGRAMMING P

All transport charges incurred in connection with warranty service or replacement will be paid by the purchaser. 2. These warranties do not cover batteries and extend only to defects in materials or workmanship occurring under normal use of the product where operated in accordance with our instructions. Philips Consumer Products Division Technology Park Figtree Drive, Australia Centre Homehush 2140 New South Wales GUARANTEE FOR NEW ZEALAND Thank-you for purchasing this quality Philips produ

•To stop playback, press 9. – The unit is switched off. – At the end of the tape, the 2 button is automatically released and the unit is switched off. •For fast winding, press 6. To stop, press 9. General Information ACCESSORIES (included) • Stereo Headphones • Belt clip USE YOUR HEAD WHEN USING HEADPHONES • Hearing safety: Do not play your headphones at a high volume. Hearing experts advise that continuous use at high volume can permanently damage hearing. • Traffic safety: Do not use headphone

Tuner reception 1 Adjust the source selector to FM or AM. 2 Turn TUNING to tune to a station. • For FM, pull out the telescopic antenna. Incline and turn the antenna. Reduce its length if the signal is too strong (very close to a transmitter). • For AM, the set is provided with a built-in antenna so the telescopic antenna is not needed. Direct the antenna by turning the whole set. 3 To switch off the radio, adjust the source selector to OFF position. CD player Display indication for CD functions

Playing a CD is then not possible. Do not attempt to clean the lens but leave the set in a warm environment until the moisture evaporates. • Always shut the CD door to keep the CD compartment dust-free.To clean, dust the compartment with a soft dry cloth. • To take a CD out of its box, press the center spindle while lifting the CD.Always pick up the CD by the edge and replace the CD back in its box after use to avoid scratching and dust. • To clean the CD, wipe in a straight line from the center