Évaluations - 3, GPA: 5
(
)
)
|
Facilité d'utilisation
That extension cord is properly wired and ingood electrical condition; and c. That wire size is at least as large as the one specified in the table below. TABLE 1 RECOMMENDED MINIMUM AWG SIZE FOR EXTENSION CORDS FOR BATTERY CHARGERS -~ Length of Cord (Feet) 25 50 100 150 AWG Size of Cord 18 18 18 16 ADDITIONAL SAFETY RULES FOR BATTERY 1. Always charge the Makita battery 122 immediately after purchase. 2. Always recharge the Makita battery 122 after use. 3. Be sure to charge the Makita battery 122 for approx. one week every six months, when not using it for long periods. If left uncharged, it may become unchargeable. 4. Use only the Makita charger Model DC122 or DC121 specified to charge the Makita battery 122. 5. Do not charge inside a box or container of any kind. 6. Do not short the battery: 1) Do not touch the terminals with any conductive material. 2) Avoid storing battery ina container with other metal objects such as nails, coins, etc. 3) Do not expose battery to water or rain. 4) Do not cut the adaptor cord. A battery short can cause a large current flow, overheating, possible burns and even a breakdown. 7. Do not leave the battery exposed to direct sunlight. Do not store the battery in locations where the temperature may reach or exceed 4OoC (104OF). 8. The Makita battery 122 contains a strong electrolyte (dilute sulfuric acid). Do not apply undue force to the battery, drop or strike it. Do not attempt to disassemble or make modifications to the battery. 9. If the battery breaks open and electrolyte (dilute sulfuric acid) contacts skin or clothing, wash immediately with running water. If electrolyte gets into your eyes, rinse them out with clear water and seek medical attention right away. IO. As the battery service life ends, its capacity and operation time decrease. Replace it with a new one. 11. Never expose the battery to flames, fire or great heat. Breakage may cause release of injurious material. ADDITIONAL SAFETY RULES FOR CHARGER 1. The Makita charger Model DC122 is specifically designed to charge only the Makita battery 121or 122. Do not attempt to charge any other battery with this charger. 2. Handle the charger carefully. Do not drop or strike it. 3.Never carry the charger by cord or yank it to disconnect from receptacle. 4. Keep cord from heat, oil, chemicals, and sharp edges. 5. Use only a power source of the same voltage as indicated on the nameplate of the charger when charging. 6. Do not attempt to use a step-up transformer, an engine generator or DC power receptacle. 7. Charge the battery at a room temperature of 10°C (5OOF) -4OoC (104OF). 8. Do not charge in place exposed to direct sunlight. 9. Do not allow the charger to get wet. IO. Do not charge inside a box or container of any kind. 11. Do not charge near volatile, flammable material such as gasoline, paint, gas, adhesive, etc. 12. Do not charge on top of paper, carpet, vinyl sheeting, cloth materials, etc. 13. Do not allow anything to cover or clog the charger vents. Do not attempt to insert anything into the vents. 14. Do not charge in dusty place. 15. Stop charging immediately if you notice anything abnormal. Ship or take the charger and the battery to your nearest Makita Service Center or Distributor for checking them. 16. Do not attempt to disassemble or make modifications to the charger. 17. Do not put any metal objects or foreign matter into the inlet of the charger. Short-circuit will occur, causing a burn injury and charger breakdown. SAVE THESE INSTRUCTIONS. DC122 DC121 122 Approx. 1 hour Approx. 2 hours 121 Approx. 2 hours Approx. 4 hours Connector Adaptor cord 4,u/ Adaptor cord--, Inlet CAUTION: 0 Always charge the Makita battery 122 immediately after purchase. 0 Always recharge the Makita battery 122 after use. If the Makita battery 122 has not been used for long periods, charge it for more than the time specified in the table above. (Example: If it has not been used for six months, charge it for approx. one week.) Charging continues even after the charging light goes out. If the battery is left uncharged for more than six months, it may become unchargeable. If the light does not come on within five minutes after you start the charging, the battery may be unchargeable. Ship or take the charger and the battery to your nearest Makita Service Center or Distributor for checking. Lock-off button \ Switch action To prevent the trigger from being acciden- tally pulled, a lock-off button is provided. To start the tool, push in the lock-off button and pull the trigger. Release the trigger to stop. CAUTION : 0 Before connecting the battery to the tool, always check to see that the switch trigger actuates properly and returns to the "OFF" position when released. Do not switch on the tool when someone is nearby or when the blades are contacting something. Connecting the battery to the tool Connect the battery to the tool using the adaptor cord. To prevent the adaptor cord from being accidentally disconnected, hook the cord to ...
Ce manuel est également adapté pour les modèles :Clippers - UML03D (718.82 kb)