Log:
Évaluations - 3, GPA: 4 ( )

Instructions Electrolux, Modèle Elite 4330X

Fabricant : Electrolux
Taille : 729.38 kb
Nom Fichier :
Langue d'enseignement: sven
Aller à la télécharger



Facilité d'utilisation


Petrol fumes can cause an explosion or a fire. Never store large amounts of fuel. To prevent possible restarting problems avoid running the fuel tank dry. This also helps to extend engine life. E. Safety guard assembly 1) In the interest of safety, it is imperative that the unit is used with the correct guard (P/N 248959 O25 P/N 248960 O30) when using any blade or a nylon string head, except the 24-80 tooth blade. Line cutter blade (L): assemble as illustrated E1. 2-3) When using a saw tooth blade (optional accessory), the correct guard must be fitted (P/N 240553). A double shoulder harness must also be worn. Only use blades or nylon string heads clearly marked with a maximum speed of at least 10,500 min-1. Follow the fitting instructions carefully. N.B: Saw tooth blades (24 - 80 tooth) have a central base diametre of 20mm and therefore require the use of the appropriate size top flange to ensure a correct fit. The part number is detailed in the cutting attachment summary chart. F. Blade and nylon string head assembly Assemble the correct guard to suit the kind of blade or nylon string head to be used (See section: SAFETY GUARD ASSEMBLY). 1) Assemble blade as illustrated: a) Flange guard - b) Upper cap with blade centering - c) Blade with text and directional arrow facing upwards - d) Lower washer - e) Fixed mower gauge - f) Blade locking screw (length mm 16). 2) If you want to assemble the rotating mower gauge,proceed as illustrated: a) Flange guard - b) Upper cap with blade centering - c) Blade with text and directional arrow facing upwards - d) Lower washer - e) Spacer - f) Rotating mower gauge - g) Blade locking screw (length mm 34,5). Replace the blade attachment bolt if damaged in any way. 3) Make sure that the blade bore opening fits perfectly around the centering collar on the upper cap. Tighten counterclockwise. While tightening, the blade assembly can be held fast by inserting the wrench or the screwdriver supplied into the cap and gearcase holes. ENGLISH - 4 To do this, rotate the cap intil the two holes 5) While tightening, the head assembly can be coincide. held fast by inserting the wrench or the screwdriver supplied into the holes as already shown 4) Assemble nylon string head as illustrated: for blade assembly. a) Flange guard - b) Upper cap - c) Guard d) Nylon string head WARNING: Do not use the guard for the nylon Tighten counterclockwise. string head when using a metal blade. G. Engine/shaft assembly BACK-PACK BRUSHCUTTER See sections BACK-PACK BRUSHCUTTER. DANGER. Do not run engine without shaft attached as clutch could fly off. 1) Assemble the engine onto the shaft. Make sure the shaft is fully and correctly engaged up to the shank, then tighten the 2 screws (A) in a criss-cross sequence. 2) Fit the end of the trigger cable connector (B) into the slot on swivel (C). 3) Adjust the screw (D) of the trigger cable connector so that the cable can easily slide in the opening with a play of 1 mm before operating the swivel (C). Tigh...

Ce manuel est également adapté pour les modèles :
Clippers - Elite 3325/34 cc (729.38 kb)
Clippers - 95390038700 (729.38 kb)
Clippers - Elite 4230X/42 cc (729.38 kb)
Clippers - Elite 4330XPro/42 cc (729.38 kb)

Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories