Keep your hands and fingers away from the switch lever (5B) while carrying the trimmer. • Nylon line continues to rotate after the trimmer has been switched off. Before Using Your 12RC 1 .Ensure the battery is fully charged. 2.(4) Adjust the steady handle to a comfortable operating position, by unscrewing the wing knob, springing the side lugs apart, moving the handle to the required position, carefully reengaging the teeth and then tightening the wing knob. (5) To Start Your 12RC 1. Press

This will speed oil consumption, and require more frequent oil tank refills. 6. To adjust oil pump to max, the control screw must be pressed in slightly prior to turning. Failure to do so could damage the pump or screw. WARNING DANGER THE OIL FLOW RATE ADJUSTING SCREW HAS 3 INCREMENTAL SETTINGS. 7. Wipe debris from around the oil fill cap prior to re-filling the oil reservoir. WARNING DANGER NEVER FILL THE OIL TANK OR ADJUST THE OIL FLOW WHILE MOTOR IS RUNNING. DISCONNECT POWER CORD FROM THE POW

Severe injuries can result if you try to use this machine with only one hand or with an insecure grip. 28. Thoroughly inspect the area where equipment is to be used and removed all objects, which can be thrown by the machine. 29. Always keep area clear of children, pets, and bystanders. 30. Always inspect your unit before each use and ensure that all handles, guards and fasteners are secure, operating, and in place. Be sure that all electrical cords are not damaged or broken. 31. Always maintain

Fitting the blade guard and saw blade • The blade guard (A) is fitted using 4 screws (L) as shown. CAUTION! Always use the recommended guard for the cutting attachment you are using. See chapter on Technical data. • Fit the drive disc (B) on the output shaft. • Turn the blade shaft until one of the holes in the drive disc aligns with the corresponding hole in the gear housing. • Insert the locking pin (C) in the hole to lock the shaft. • Place the blade (D) and support flange (F) on the output s

X English – 33 TECHNICAL DATA Technical data Note 1: Noise emissions in the environment measured as sound power (LWA) in conformity with EC directive 2000/14/EC. Note 2: Equivalent sound pressure level is calculated as the time-weighted energy total for sound pressure levels under various working conditions with the following time distribution: 1/2 idling and 1/2 max speed. NOTE! The noise pressure level at operator’s ear and vibrations on the handles are measured with all the approved cutting a

KEEP A FIRM GRIP WITH BOTH HANDS WHILE BLADES ARE MOVING AND/OR MOTOR IS RUNNING. KEEP A SURE FOOTING. DO NOT OVERREACH. IF YOUR TRIMMER BECOMES JAMMED, RELEASE SWITCH AND STOP MOTOR. MAKE SURE BLADES HAVE STOPPED COMPLETELY. UNPLUG THE UNIT, THEN REMOVE THE OBSTRUCTION. WARNING – DANGER SWITCH OFF THE MOTOR AND UNPLUG THE UNIT BEFORE LUBRICATING OR ADJUSTING THE BLADES. 1.To adjust the blade angle, first shut off the motor. Next, grip the blade adjustment handle. Then move the quick release lev

2 Keep the teeth of the blade correctly sharpened! Follow our instructions and use the recommended file gauge. An incorrectly sharpened or damaged blade increases the risk of accidents. 3 Maintain the correct blade setting! Follow our instructions and use the recommended blade setting tool. An incorrectly set blade increases the risk of jamming and kickback. 4 Check the cutting attachment for damage or cracks. A damaged cutting attachment should always be replaced. Quick release Check that the h

A muffler fitted with a catalytic converter is also designed to reduce harmful exhaust gases. In countries that have a warm and dry climate there is a significant risk of fire. We therefore fit certain mufflers with a spark arrestor mesh. Check whether the muffler on your machine is fitted with this kind of mesh. For mufflers it is very important that you follow the instructions on checking, maintaining and servicing your machine. 8 – English GENERAL SAFETY PRECAUTIONS Never use a machine that h

Your warranty may not cover damage or liability caused by the use of non-authorized accessories or replacement parts. ! WARNING! A clearing saw, brushcutter or trimmer can be dangerous if used incorrectly or carelessly, and can cause serious or fatal injury to the operator or others. It is extremely important that you read and understand the contents of this operator’s manual. This label certify that the product has been certified in accordance with American exhaust requirements EPA 1. English –

Always use genuine accessories. Non-authorised modifications and/or accessories can result in serious personal injury or the death of the operator or others. Your warranty does not cover damage or liability caused by the use of non- authorized accessories or replacement parts. IMPORTANT ENGINE INFORMATION HUSQVARNA AB HUSKVARNA SWEDEN TWC REFER TO OPERATOR`S MANUAL FOR MAINTENANCE SPECIFICATIONS AND ADJUSTMENTS. FOR SMALL NON - ROAD ENGINES. EPTHIS ENGINE CONFORMS TO U.S. PH1A This decal certifi