. . . . . . . . . . . . . . . .791-153066 Fuel Cap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .791-181612 Shoulder Harness . . . . . . . . . . . . . . . . . . . . . . . .791-682075B Tip-and-Pour 2-Cycle Oil (16 oz.) . . . . . . . . . . . . . .791-180965 These replacement parts can be purchased at the retailer from which you bought your trimmer, or your local Cub Cadet dealer. CLEANING To avoid serious personal injury, always turn your trimmer off and allow it to cool before yo

Start the engine and let it run at a high idle for a minute to warm up. 2. Release the throttle trigger and let the engine idle. If the engine stops, insert a small phillips or flat blade screwdriver into the screw next to the air filter cover (Fig. 6-15). Turn the idle speed screw in, clockwise, 1/8 of a turn at a time (as needed) until the engine idles smoothly. NOTE: The cutting attachment should not rotate when the engine idles. 3. If the cutting attachment rotates when the engine idles, tur

Use a 40:1 fuel/oil ratio. Do not mix them directly in the engine fuel tank. See the table below for specific gas and oil mixing ratios. NOTE: One gallon (3.8 liters) of unleaded gasoline mixed with one 3.2 oz. (95 ml) bottle of 2-cycle oil makes a 40:1 fuel/oil ratio. Gasoline is extremely flammable. Ignited Vapors may explode. Always stop the engine and allow it to cool before filling the fuel tank. Do not smoke while filling the tank. Keep sparks and open flames at a distance from the area. R

We reserve the right to make changes at any time without notice. Copyright© 2007 MTD SOUTHWEST INC, All Rights Reserved. WARNING: When using the unit, you must follow the safety rules. Please read these instructions before operating the unit in order to ensure the safety of the operator and any bystanders. Please keep these instructions for later use. P/N 769-02763 (1/07) WARNING THE ENGINE EXHAUST FROM THIS PRODUCT CONTAINS CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER, BIRTH DEFEC

• Be sure the cutting attachment is not in contact with anything before starting the unit. • Use the unit only in daylight or good artificial light. •Avoid accidental starting. Be in the starting position whenever pulling the starter rope. The operator and unit must be in a stable position while starting. See Section 5, Operation. • Use the right tool. Only use this tool for the purpose intended. • Do not overreach. Always keep proper footing and balance. • Always hold the unit with both hands w

You must read and understand this Operator’s Manual and especially the Safety Precautions for proper and safe operation. Cub Cadet Commercial's philosophy is to continually improve all of its products. As a result, engineering changes and improvements are made from time to time. If the operating characteristics or the appearance of your clipper differ from those described in this Operator’s Manual, please contact your Cub Cadet Commercial dealer for information and assistance. Contact your Cub

For more details about your unit, visit our website at DO NOT RETURN THE UNIT TO THE RETAILER. PROOF OF PURCHASE WILL BE REQUIRED FOR WARRANTY SERVICE. THIS PRODUCT IS COVERED BY ONE OR MORE U.S. PATENTS. OTHER PATENTS PENDING. Service on this unit both within and after the warranty period should be performed only by an authorized and approved service dealer. TABLE OF CONTENTS Service Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Rules for Safe Operation . . . . . . .

31). Turn the idle speed screw in, clockwise, 1/8 of a turn at a time (as needed) until the engine idles smoothly. NOTE: The cutting attachment should not rotate when the engine idles. 3. If the cutting attachment rotates when the engine idles, turn the idle speed screw counterclockwise 1/8 of a turn at a time (as needed), to reduce idle speed. Checking the fuel, cleaning the air filter, and adjusting the idle speed should solve most engine problems. If not and all of the following are true: • t

If you have any questions regarding your warranty rights and responsibilities, you should call 1-877-282-8684. Manufacturer’s Warranty Coverage • The warranty period begins on the date the engine or equipment is delivered to the retail purchaser. • The manufacturer warrants to the initial owner and each subsequent purchaser, that the engine is free from defects in material and workmanship which cause the failure of a warranted part for a period of two years. • Repair or replacement of warranted