Cruise control lever OFF ON ADJUSTMENT OF IDLING DANGER The carburetor is the adjustment being completed at the time of factory shipment. Please do not adjust other than idling adjusting. When adjustment becomes necessary, please consult your dealership or an authorized service agent. Checkup of low-speed rotation Set the low-speed rotation to 3500 ( /min). • If it is necessary to change the rotation speed, regulate the adjusting screw, with Phillips screwdriver. • Turn the adjusting screw to th

Remedy Engine does not start Failure to operate primer pump Push 7 to 10 times. Low pulling speed of starter rope Pull strongly. Lack of fuel Feed fuel. Clogged fuel filter Clean Broken fuel tube Straighten fuel tube Deteriorated fuel Deteriorated fuel makes starting more difficult. Replace with new one. (Recommended replacement: 1 month) Excessive suction of fuel Set throttle lever from medium speed to high speed, and pull starter handle until engine starts. If engine will not start still, remo

REFUELING METHOD • Loosen the tank cap a little so that there will be no difference in atmospheric pressure. • Detach the tank cap, and refuel, discharging air by tilting the fuel tank so that the refuel port will be oriented upward. (Never refill fuel full to the oil refill port.) • After refueling, securely tighten the tank cap. • If there is any flaw or damage on the tank cap, replace it. • The tank cap is consumable, and therefore should be renewed every two to three years. 10 OPERATION 1. S

Inspection and Refill of Engine Oil (1) Perform the following procedure, with the engine cooled down. • Inspection: Please inspect whether it makes the machine horizontal, removes the oil cap, there is a oil to inside the range of the upper limit lower limit mark of gauge. When it is insufficient, (especially, when it has not reached to the lower limit level), please refill new oil. • Refill: Verticality (under the suction port cover) please do the machine, remove the oil cap. When oil is suppli

and spray-type lubricating oil. CAUTION: • Do not wash the blades in water. Failure to do so may cause rust or damage on the tool. 7 Removing or installing shear blade Removing or installing shear blade CAUTION: • Before removing or installing shear blade, always be sure that the tool is switched off and unplugged. • When replacing the shear blade, always wear gloves without removing blade cover so that hands and face does not directly contact the blade. Failure to do so may cause personal injur

D-22004 Hamburg .. Germany 995 700 191 (D, GB, F, E) MS-330 C, MS-330 C (USA) , MS-330 U, MS-330 U (USA) 1 Kurbelgehause Crankcase Carter-vilebrequin Carter ciguenal 1113961111109124671538245 MS-330 C, MS-330 C (USA) , MS-330 U, MS-330 U (USA) 1 Kurbelgehause Crankcase Carter-vilebrequin Carter ciguenal Seite / PagePos. MS-330 CMS-330 C (USA) MS-330 UMS-330 U (USA) Teil-Nr. Part No. No. de piece No. de pieza Hinweise Notes Renseign. Nota Bezeichnung Spezifikation Specification Description Design

995 700 253 (GB) DOLMAR GmbH • Postfach 70 04 20 • D-22004 Hamburg • Germany LT-210 1 Pipe, handle, protector, gear case 2005/11 1 5 6 7 8 3 2 17 18 19 20 21 22 24 25 23 26 27 28 30 16 4 9 10 12 11 14 13 15 29 LT210 1/3 LT-210 PagePos. LT-210LT-250Part No. Notes Description Specifications 1 1 1 381 450 070 GRIP 1 2 1 381 502 800 CONTROL LEVER ASSY INC. 3,5-12 1 3 1 381 501 811 WIRE SET INC. 4 1 4 1 381 501 812 CONTROL CABLE 1 5 1 381 501 805 TUBE 1 6 3 381 350 530 SCREW ASSEMBLY M5X30(SW) 1 7 1

Push up the projection and slide the cover in the “OPEN” direction. When closing the cover, slide the cover in the “CLOSE” direction till the click under the plug cover projection rides over the engine cover. Finally, push in the projection. (2) Removing the spark plug Use an attached box wrench to remove or install the spark plug. (3) Checking the spark plug The clearance between two electrodes of spark plug (see the figure left) is 0.7 to 0.8 mm. Adjust to the correct clearance when it is too

• Never use the blower while under the influence of alcohol or drugs (2). • Do not use the unit when you are tired. • Save these instructions for future referral. Personal Protective Equipment • The clothing worn should be functional and appropriate, I. e. It should be tight-fitting but not cause a hinderance. Do not wear jewelry, clothing or long hair which could be drawn into the air intake. • In order to avoid head-, eye-, hand- or foot injuries as well as to protect your hearing the followin

Always wear protective gloves! CAUTION : Start the blower only after having assembled itcompletely. 1. ASSEMBLY OF BLOWER PIPES 1) Align grooves in the blower pipe with pegs on the blower housing and slide the pipe onto housing. 2) Turn the blower pipe clockwise to lock it into place. 2. ASSEMBLY OF VACUUM ATTACHMENT 1) Installing Vacuum pipe (nozzle) (1) Loosen the screw . and open the protector . . WARNING! When using this machine as a blower, be sure to confirm that the screw . is not loosene