Évaluations - , GPA:
(
)
)
Fabricant : Gigabyte
Taille : 322.17 kb
Nom Fichier :
Langue d'enseignement: 
Le document est chargé, s'il vous plaît patienter
 |
Le document est chargé, s'il vous plaît patienter
Facilité d'utilisation
2 ( ) Installing SATA hard drive(s) in your computer ...................................................................... 2 ( ) Configuring SATA controller mode and boot sequence in BIOS Setup .................................. 2 ( ) Configuring RAID set in RAID BIOS ........................................................................................ 6 ( ) Making a SATA controller driver disk ..................................................................................... 9 ( ) Installing SATA controller driver during OS installation ......................................................... 11 ( ) Configuring a bootable RAID array with Microsoft Windows 2000 ...................................... 14 Configuring SATA Hard Drive(s) (Controller: nVIDIA nForce4 SLI) To configure SATA hard drive(s), follow the steps below: (1) Install SATA hard drive(s) in your system. (2) Configure SATA controller mode and boot sequence in BIOS Setup. (3)* Configure RAID set in RAID BIOS. (4) Make a floppy disk containing the SATA controller driver. (5) Install the SATA controller driver during OS installation. Before you begin Plea se prep are: (a) At least two SATA hard drives (to ensure optimal performance, it is recommended that you use two hard drives with identical model and capacity). If you do not want to create RAID, you may prepare on ly o ne h ard driv e. (b) An empty formatted floppy disk. (c) Wind ows XP /2000 s etup d isk. (d) Driver CD for your motherboard. (1) Installing SATA hard drive(s) in your computer Attach one end of the SATA signal cable to the rear of the SATA hard drive and the other end to available SATA port(s) on the motherboard. If there are more than one SATA controller on your motherboard, you may r efer to t he mother board us er's manu al to ide ntify the SATA con troller for the c onnector. Then connect the power connector from yo ur power supply to the hard drive. (2) Configuring SATA controller mode and boot sequence in BIOS Setup You have to make sure whether the SATA controller is configured correctly in system BIOS Setup and set BIOS boot sequence for the SATA hard drive(s)/RAID array. Step 1: Turn on your computer and press Del to enter BIOS Setup during POST (Power-On Self Test). In the example in Figure 1, make sure that Serial-ATAII 1 or Serial-ATAII 2 under the Integrated Peripherals menu is enab led (Seri al-ATA II1 con trols the SAT AII0/1 connec tors a nd Seri al-ATA II2 co ntro ls t he SA TAI I2/ 3 c onn ect ors ). If you wish to c rea te RAI D a rra y, pre ss ENT ER on the ID E/S ATA II RA ID Config item to enter the submenu . "*" Skip this step if you do not want to create RAID array on the SATA controller. SATA Configurations (P4 nForce4 SLI series) -2 CMOS Setup Utility Copyright (C) 1984 2005 Award Software Integrated Peripherals On-Chip IDE Channel0 [Enabled] On-Chip IDE Channel1 [Enabled] IDE1 Conductor Cable [Auto] IDE2 Conductor Cable [Auto] On-Chip USB [V1.1+V2.0] USB Keyboard Support [Disabled] USB Mouse Support [Disabled] AC97 Audio [Auto] Onboard LAN2 Function [Auto] Onboard SATAII/IDE3 [Enabled ] Onboard SATAII/IDE3 Mode [BASE] Onboard 1394b Function [Enabled] Onboard LAN Function [Enabled] Onboard Serial Port 1 [3F8/IRQ4] i-Lock [Enabled] Onboard Parallel Port [378/IRQ7] Parallel Port Mode [SPP] Item Help Menu Level} higf: Move Enter: Select +/ /PU/P D: Value F10: Save ESC: Exit F1: General Help F3: Language F5: Previous Values F6: Fail Safe Defaults F7: Optimized Defaults Figu re 1 In the IDE/SATAII RAID Config submenu, enable IDE/SATAII RAID function. Then enable the SATA ports with hard disks that you want to use for RAID. In the example in Figure 2, enable SATAII 1 Primary/ Secondary RAID or SATAII 2 Primary/Secondary RAID). (For example, if you wish to create RAID with hard disks on the SATAII0 and SATAII1 connectors, set SATAII 1 Primary/Secondary RAID to E na b l ed ) . CMOS Setup Utility Copyright (C) 1984 2005 Award Software IDE/SATAII RAID Config Item Help Menu Level}IDE Primary Master RAID [Disabled] IDE Primary Slave RAID [Disabled] IDE Secndry Master RAID [Disabled] IDE Secndry Slave RAID [Disabled] higf: Move Enter: Select +/ /PU/P D: Value F10: Save ESC: Exit F1: General Help F3: Language F5: Previous Values F6: Fail Safe Defaults F7: Optimized Defaults Figu re 2 Th e B IOS Se tu p m enu s d esc rib ed in th is sec tio n m ay not s how th e e xac t s ett in gs for yo ur motherboard. The actual BIOS Setup menu options you will see shall depend on the motherboard you have and th e BIOS version. -3 -SATA Configurations (P4 nForce4 SLI series) Step 2: If you do not create RAID, select Hard Disk Boot Priority under the Advanced BIOS Features menu. In the Hard Disk Boot Priority submenu, select the model of the SATA hard drive onto which you wish to install Microsoft Windows 2000/XP. You should see a screen similar to Figure 3 below. CMOS Setup Utility Copyright (C) 1984 2005 Award Software Hard Disk Boot Priority 1. CH2 M. : ST3120026AS 2. CH3 ...