Évaluations - 3, GPA: 3.7
(
)
)
|
Facilité d'utilisation
To remove Tires 1. Using a 1/8" hex head wrench loosen set screw in hub collar. 2. Slide hub collar from axle and remove the tire. STorAGE Engine U Consult the engine instruction manual for the manufacturer's recommendations for storage. Pump The manufacturer recommends using a pump protector/winterizer, such as DeWALT winterizer (DP80) when storing the unit for more than 30 days and/or when freezing temperatures are expected. DeWALT winterizer (DP80) is availabe at the store where the pressure washer was purchased. If a pump protector/ winterizer is not available, RV antifreeze can be used as outlined in the following steps. note: Using a pump protector/ winterizer or RV antifreeze helps to provide proper lubrication to the internal seals of the pump regardless of temperature or environment. 1. Obtain a funnel, 6 oz. (170 mL) of RV antifreeze and 16–36" (40–91cm) of garden hose with a male hose connector attached to one end. CAUTION: risk of property damage. Use only rv antifreeze. Any other antifreeze is corrosive and can damage pump. 2. Disconnect spark plug wire. 3. Connect length of garden hose to water inlet of pump. 4. Add RV antifreeze to hose as shown. 5. Pull engine starter rope slowly several times until antifreeze comes out of high-pressure hose connection of pump. 6. Remove garden hose from water inlet of pump. 7. Reconnect spark plug wire. Pressure Washer 1. Drain all water from high- pressure hose, coil it and store it in cradle of the pressure washer handle. 2. With nozzle pointed down and the spray gun and wand in a vertical position, squeeze trigger to drain all water from spray gun and wand. Store in gun holder. 3. Store chemical hose so it is protected from damage. 4. If space is needed, handles may be removed and attached as shown. English 15 EnglishEnglish CAUTION: Risk of personal injury. Avoid placing hands between handle and frame when assembling to prevent pinching. AccESSorIES Recommended accessories for use with your tool are available for purchase from your local dealer or authorized service center. If you need assistance in locating any accessory for your tool, please contact DeWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286, call 1-800-4-DeWALT (1-800-433-9258) or visit our website DANGER: Risk of fluid injection. When using replacement lances or guns with this pressure washer, DO NOT use a lance and/or lance/gun combination that is shorter in length than what was provided with this pressure washer as measured from the nozzle end of the lance to the gun trigger. WARNING: The use of any other accessory not recommended for use with this tool could be hazardous. Use only accessories rated equal to or higher than the rating of the pressure washer. SErvIcE InForMATIon Please have the following information available for all service calls: Model Number ____________ Serial Number ___________ Date and Place of Purchase ____________________________ repairs To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment should be performed by a DeWALT factory service center, a DeWALT authorized service center or other qualified service personnel. Always use identical replacement parts. Limited Warranty DeWALT pressure washers are warranted for two years from the date of purchase. DeWALT will repair, without charge, any defects due to faulty materials or workmanship. This warranty does not cover parts that are damaged through misuse or abuse, or parts which must be replaced from time to time due to normal pressure washer operation. Normal wear parts include, but are not limited to, the engine air filter, spark plug, pump valve seals and O rings. This warranty does not apply to accessories or damage caused where repairs have been made or attempted by a repair center not authorized by DeWALT. This warranty gives you specific legal rights and you may have other rights which vary in certain states or provinces. For further details of warranty coverage and warranty repair information, visit and click on Service and Support or call 1-800-4-DeWALT (1-800-433-9258). LatIn aMerIca: This warranty does not apply to products sold in Latin America. For products sold in Latin America, see country specific warranty information contained either in the packaging, call the local company or see website for warranty information. 16 17 English FREE WARNING LABEL REPLACE MENT: If your warning labels (next page) become illegible or are missing, call 1-800-4-DeWALT for a free replacement. Glossary Bypass mode: Allows water to re-circulate within pump when the gun trigger is not pulled. Chemical hose: Feeds cleaning agents into the pump to mix with the water. Refer to Chemicals and Cleaning Solvents. Chemical injection system: Mixes cleaners or cleaning solvents with water to improve cleaning effectiveness. Choke control: Opens and closes carburetor choke valve. CU: Cleaning Units. GPM multiplied by PSI. (GPM x PSI = CU) Fuel valve lever: Opens/close...