Évaluations - 4, GPA: 4.3
(
)
)
|
Facilité d'utilisation
Confirm the bands by pressing TUNER/ BAND repeatedly. 1/u 4 31 (power) 225 1 Press TUNER/BAND repeatedly until the band you want appears in the display. Every time you press this button, the band changes as follows: 2 band model: FM .AM 3 band model: FM nMW nLW 2 Press and hold + or – until the frequency indication starts to change automatically, then release it. Scanning stops when the system tunes in a station. “TUNED” and “STEREO” (for a stereo program) appear. TUNED STEREO VOLUME ALL DISCS MHz 3 Press REPEAT/MEMORY. A preset number appears in the display. TUNED STEREO VOLUME ALL DISCS Preset number 4 Turn the jog dial to select the preset number you want. 5 Press ENTER/NEXT. The station is stored. 6 Repeat steps 1 to 5 to store other stations. continued n Step 3: Presetting radio stations (continued) To tune in a station with a weak signal When the desired station is skipped during automatic tuning, press + or – repeatedly in step 2 to tune in the station manually. To change the preset number Start over from step 1. To change the AM tuning interval (for models with the AM TUNING STEP switch on the rear panel) The AM tuning interval is factory-preset to 9 kHz (10 kHz in some areas). To change the AM tuning interval, turn off the power and set the AM TUNING STEP switch on the rear panel to 10 kHz (or 9 kHz). Then turn the power back on. When you change the interval, all the preset stations will be erased. Tip The preset stations are retained for half a day even if you unplug the power cord or if a power failure occurs. Connecting optional AV components To enhance your system, you can connect optional components. Refer to the instructions of each component. Connecting audio components Select one of the following two connections, depending on the equipment to be connected and method of connecting. Connecting an MD deck for digital recording You can record from CD into the MD deck digitally by connecting an optical cable (not supplied). To the DIGITAL IN connector of the MD deck Connecting an MD deck for analog recording Make sure to match the color of the plugs and the connectors. To listen to the sound of the connected MD deck, press FUNCTION repeatedly until “MD” appears. To the input of To the output the MD deck of the MD deck AM antenna Connect a 6- to 15- meter (20- to 50- feet) insulated wire to the AM antenna terminal.antennas Leave the supplied AM loop antenna connected. Connecting outdoor Jack type A Connect the outdoor antenna to improve the reception. Insulated wire FM antenna Connect the optional FM outdoor antenna. You can also use the TV antenna instead. Jack type A (not supplied) Screw clamp AM GND FM(75 ) Ground wire (not supplied) 75-ohm coaxial cable (not supplied) AM GND FM(75 ) Ground wire (not supplied) Jack type B Screw clamp Jack type B Insulated wire (not supplied) IEC standard socket connector (not supplied) AM FM(75 ) AM FM(75 ) Ground wire (not supplied) Ground wire (not supplied) Screw clamp Important Screw clamp GND If you connect an outdoor antenna, ground from GND yterminal below the SPEAKER jacks with the screw clamp. To prevent a gas explosion, do not connect the ground wire to a gas pipe. Basic Operations Basic Operations 1 Press 6and place up to two CDs on Playing a CD the disc tray. — Normal play If a disc is not placed properly, it will not be recognized. You can play up to three CDs in a row. . With the label1/u CD (P 2 DISC SKIP 1 side up. When (power) you play a single CD, place it on the inner circle of the tray. To insert a third disc, press DISC SKIP to rotate the disc tray. 2 Press one of the DISC 1 – 3 buttons. The disc tray closes and play starts. If you press CD (P(or CD (on the remote) when the disc tray is closed, play starts from the CD loaded on the tray whose button is lit green. Disc tray number PLAY MODE Jog dial DISC SKIP P Track number Playing time 1/u (power) p 0 continued ) + =/+ 0/) CD ( VOL +/– p0)VOLUME Basic OperationsALL DISC VOLUME = (Pp( ( Playing a CD (continued) Tips To Do this Stop play Press p. Pause Press CD (P(or Pon the remote). Press again to resume play. Go to the next track or go back to the start of the current track During play or pause, turn the jog dial clockwise (to go forward) or counterclockwise (to go back). (Or press + (to go forward) or =(to go back) on the remote.) Find a point in Press and hold down ) or a track 0during play and release it at the desired point. Select a CD Press DISC SKIP. in stop mode Play only the Press PLAY MODE repeatedly CD you have until “1 DISC” appears. selected Play all CDs Press PLAY MODE repeatedly until “ALL DISCS” appears. Remove the CD Press 6in stop mode. Exchange other Press 6. CDs while playing Adjust the Turn VOLUME (or press volume VOL +/– on the remote). • Pressing CD (P when the power is off automatically turns the power on and starts CD playback if there is a CD in the tray (One Touch Play). • You can switch from another source to the CD player and start playing a CD just by pressing...
Ce manuel est également adapté pour les modèles :Stéréo - MHC-R300 (425.88 kb)
Stéréo - MHC-R500 (425.88 kb)
Stéréo - MHC-RX55 (425.88 kb)