Évaluations - 3, GPA: 3.3
(
)
)
|
Facilité d'utilisation
• This instrument is designed to minimize the extraneous sounds produced when it’s played. However, since sound vibrations can be transmitted through floors and walls to a greater degree than expected, take care not to allow these sounds to become a nuisance to neighbors, especially when performing at night and when using headphones. 3 4 When mounting the CY-5 on a cymbal stand, use ONLY the attachment set as shown below. fig.CY-03.j 1. Mount the cymbal stopper as shown below. The cymbal stopper keeps the cymbal from rotating, allowing proper function of the pad, and also prevents cables from winding around the stand. 2. Attach the CY-5 so the Roland logo is positioned on the opposite side of the playing area. 3. Tighten the felt washer and the wing nut. Wing Nut tension The wing nut should be tightened to allow the movement you desire. BUT, if it is too loose, double triggering may occur. Use ONLY the included felt washer and wing nut. Standard, metal wing nuts found on most cymbal stands should never be used. 4. Use the included connection cable and connect the output jack of the CY-5 to the trigger input jack of the percussion sound module. Connect the L-shaped plug of the included cable to the CY-5. To make use of edge shot and choking play techniques, you’ll need to connect to a trigger input jack on the percussion sound module that accommodates rim shots (p. 6). 921 * To prevent malfunction and/or damage to speakers or other devices, always turn down the volume, and turn off the power on all devices before making any connections. 5. Secure the cable with the provided cable tie. Leave enough slack, so that the cymbal can still move freely, without pulling on the cable. 6. For the CY-5 to function correctly, the trigger type and trigger parameters in the sound module must be adjusted. See Page 6. Making the Settings Using the CY-5 as a cymbal pad Felt Washer Wing Nut Stopper Stopper (Be sure to orient it correctly) Tighten the bolt with a drum key. Wing Nut Felt Washer Wind a cable tie around the pipe and tighten it in order to not to slip. Insert the small plastic hook to a hole to secure the cable to the cymbal arm. Be sure to make this small plastic hook visible from you. Wind a cable tie around a cable. Secure the cable in place with the cable tie Leave some slack in the cable 5 When mounting the CY-5 on an L-Rod (pad mount), use ONLY the attachment set as shown below. Acceptable rod diameters: 10.5–11.5 mm (7/16 to 1/2 inch) 1. Mounting the lower clutch and the clutch felt (L). Align the notched section as shown below. Then place the clutch felt so it fits securely. 2. Mount the CY-5 so it fits the lower clutch as shown below. 3. Place the clutch felt (S), and while applying some pressure, mount the upper clutch as shown. Afterwards, you can adjust the upper clutch to have the movement you desire. If it is too loose, double triggering may occur. Be sure the Roland logo is on the opposite side of the playing area. 4. Use the included connection cable and connect the output jack of the CY-5 to the trigger input jack of the percussion sound module. Connect the L-shaped plug of the included cable to the CY-5. To make use of edge shot and choking play techniques, you’ll need to connect to a trigger input jack on the percussion sound module that accommodates rim shots (p. 6). 921 * To prevent malfunction and/or damage to speakers or other devices, always turn down the volume, and turn off the power on all devices before making any connections. 5. Secure the cable with the provided cable tie to the stand pipe. Leave enough slack, so that the pad can still move freely without pulling on the cable. 6. For the CY-5 to function correctly, the trigger type in the sound module must be adjusted. See page 6. Using the CY-5 as a hi-hat pad Upper Clutch Clutch Felt (L) Lower Clutch Clutch Felt (S) Notch (Be sure to orient it correctly) Tighten the bolt with a drum key. Projection (Be sure to orient it correctly) Tighten the bolt with a drum key. Apply pressure Secure the cable in place with the cable tie Leave some slack in the cable Trigger Settings For Percussion Sound Module Trigger Settings For Percussion Sound Module e different depending on the module you are using. Below you will find the parameters that correspond to different sound modules. Make the trigger type setting for the percussion sound module. TD-3 (Percussion Sound Module) Trigger Type ( ): Cy ( ) Only the inputs listed below are capable of producing an edge shot and a choking play techniques. • SNARE • HI-HAT • CRASH1 • CRASH2 • RIDE TD-6V (Percussion Sound Module) TrigTyp: Cy Type TD-12/TD-20 (Percussion Sound Module) Trig Type: CY6 Playing Methods Playing Methods Do NOT play on the hard plastic section of the pad. Bow Shot This is the most common playing method, playing the pad face of the cymbal. It corresponds to the sound of the “head-side” of the connected trigger input. Bow Edge Shot This playing method involves striking the edge with the...