Évaluations - , GPA: ( )

Instructions Yamaha, Modèle YAS-101

Fabricant : Yamaha
Taille : 3.39 mb
Nom Fichier :

Langue d'enseignement:

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

Replace the batteries. — The button of the unit was not pressed long enough for the remote control learning operation. Press the button of TV remote control in the order “press 1 second” > “release 1 second” > “press 1 second” 9 The TV remote control is not available for remote control learning. Use the remote control of the unit. 9 The TV remote control is outside of the operation range. Point your TV remote control towards the remote control sensor of the unit keeping a distance of 30 cm (1 ft) between them. 9 The unit does not enter the remote control learning mode. Operate after checking that the INPUT indicator is flashing in red. 9 The power state of the unit and of your TV is opposite. (For example, though your TV is on, the unit is in standby mode.) The power state of the unit and of your TV is opposite from the beginning. Press the power button of TV remote control to set your TV and the unit to standby mode after pressing the power button of your TV itself and of the unit to set both your TV and the unit to on. 9 The TV remote control is not working even if you use the TV remote control signal transmission function. The unit and TV are too close/far from one another. Try to use the TV remote control signal transmission function again after repositioning the IR flasher of the unit and the remote control sensor of your TV. 9 Try to use the TV remote control signal transmission function again after adjusting the height of the unit by removing or attaching its stands. 9 Something is between the unit and your TV. Remove the obstruction. — The TV remote control signal transmission function is not activated. Restart the unit and check the indicator status. 9 The TV remote control is not compatible with the TV remote control signal transmission function. Place the unit (without the stands, for example) so as not to hide the remote control sensor of your TV. 9 You cannot use 3D glasses. The unit obstructs the 3D glasses transmitter of your TV. Check the position of 3D glasses transmitter of your TV by referring to the manual of your TV, and move the unit to the position where there is no obstruction. — The picture on your TV screen becomes blurred or distorted. The unit is too close to your CRT TV. Move the unit away from your TV. — Contact your nearest authorized Yamaha dealer or service center if the following problem occurs. Problem Cause Solution See page The power of the unit immediately shuts off, and the INPUT indicator flashes. The protection circuit is activated. — English 13 En Specification Specification Amplifier section • Minimum RMS Output Power Front Left and Right (1 kHz, 1% THD, 6 .) .......................................................................24 W + 24 W Subwoofer (100 Hz, 1% THD, 3 .)...........................48 W • Maximum Power Front Left and Right (1 kHz, 10% THD, 6 .) .......................................................................30 W + 30 W Subwoofer (100 Hz, 10% THD, 3 .).........................60 W Speaker section •Type Front speaker ........................... Accoustic suspension type/ Non-magnetic shielding type Subwoofer.................................................Bass reflex type/ Non-magnetic shielding type • Driver Front speaker .............................6.5 cm (2-1/2 in) cone . 2 Subwoofer........................................7.5 cm (3 in) cone . 2 • Impedance Front speaker .................................................................6 . Subwoofer......................................................................3 . • Frequency Response (-10 dB, Stereo mode) Front speaker .......................................... 150 Hz to 20 kHz Subwoofer.................................................50 Hz to 150 Hz This system employs new technologies and algorithms that make it possible to achieve 7-channel surround sound with only front speakers, and without using wall reflections. Manufactured under license from Dolby Laboratories. Dolby, Pro Logic and the double-D symbol are trademarks of Dolby Laboratories. Input Jacks • Optical......................................................2 (TV,BD/DVD) • Coaxial ................................................................... 1 (STB) Output Jacks • Subwoofer ......................................................................... 1 • System Connector (for subwoofer power interlock)......... 1 General • Power Supply [U.S.A. and Canada models]................... AC 120 V, 60 Hz [Taiwan model] ........................................ AC 110 V, 60Hz [Other models] ............................AC 220-240 V, 50/60 Hz • Power Consumption....................................................22 W • Standby Power Consumption.................... Less than 0.5 W • Dimensions (W . H . D) With stands.......................................890 . 107 .120.5 mm (35-1/8 . 4-1/4 . 4-3/4 in) • Weight........................................................4.2 kg (9.3 lbs.) * Specifications are subject to change without not...