Évaluations - 2, GPA: 4.5
(
)
)
|
Par ce dispositif a également d'autres instructions :
Facilité d'utilisation
Durch Bedienung der Bedienelemente auf dem Bedienfeld (ausgenommen der Fader), oder der Bedienelemente im Display wahrend des Gedruckthaltens dieser Taste werden die zugehorigen Informationen angezeigt. MONITOR ON MASTER (FADER ASSIGN MODE) STEREO MASTER LATCH Die Taste schaltet um, ob der STEREO-MASTER-Fader zur Einstellung des Monitorpegels verwendet wird oder nicht. UNLATCH Der STEREO-MASTER-Fader wird verwendet, um bei gedruckt gehaltener Taste den Monitorpegel einzustellen. MONO MASTER LATCH Die Taste schaltet um, ob der MONO-MASTER-Fader zur Einstellung des Monitorpegels verwendet wird oder nicht. UNLATCH Der MONO-MASTER-Fader wird verwendet, um bei gedruckt gehaltener Taste den Monitorpegel einzustellen. HOME SELECTED CH VIEW — Z eigt den SELECTED-CHANNEL-VIEW-Bildschirm an. OVERVIEW — Zeigt den OVERVIEW-Bildschirm an. MOMENTARY — Mit jedem Druck auf die Taste erscheinen abwechselnd der SELECTED-CHANNEL-VIEW-Bildschirm und der OVERVIEW- Bildschirm. Anhange 281 M7CL – Bedienungsanleitung MIDI-Datenformat MIDI-Datenformat MIDI-Datenformat MIDI-Datenformat In diesem Abschnitt wird das Datenformat beschrieben, das das M7CL interpretieren, senden und empfangen kann. 1 CHANNEL MESSAGE 1.1 NOTE OFF (8n) Reception These messages are echoed to MIDI OUT if [OTHER ECHO] is ON. They are received if [Rx CH] matches, and used to control effects. STATUS 1000nnnn 8n Note off message DATA 0nnnnnnn nn Note number 0vvvvvvv vv Velocity(ignored) 1.2 NOTE ON (9n) Reception These messages are echoed to MIDI OUT if [OTHER ECHO] is ON. They are received if [Rx CH] matches, and used to control effects. STATUS 1001nnnn 9n Note on message DATA 0nnnnnnn nn Note number 0vvvvvvv vv Velocity (1-127:on, 0:off) 1.3 CONTROL CHANGE (Bn) Two types of control change can be transmitted and received; [NRPN] (Non- Registered Parameter Numbers) and freely-assigned [TABLE] (1CH x 110) messages. Select either [TABLE] or [NRPN]. Reception These messages are echoed to MIDI OUT if [Control Change ECHO] is ON. If [TABLE] is selected, these messages are received when [Control Change Rx] is ON and [Rx CH] matches, and will control parameters according to the settings of the [Control assign table]. For the parameters that can be assigned, refer to “Parameter, die Controllern zugewiesen werden konnen” on page 270. If [NRPN] is selected, these messages are received when [Control Change Rx] is ON and the [Rx CH] matches; the four messages NRPN control number (62h, 63h) and DATA ENTRY control number (06h, 26h) are used to control the specified parameter. Transmission If [TABLE] is selected, and if [Control Change Tx] is ON when you operate a parameter that is assigned in the [Control assign table], these messages will be transmitted on the [Tx CH] channel. For the parameters that can be assigned, refer to “Parameter, die Controllern zugewiesen werden konnen” on page 270. If [NRPN] is selected, and if [Control Change Tx] is ON when you operate a specified parameter, the four messages NRPN control number (62h, 63h) and DATA ENTRY control number (06h, 26h) are transmitted on the [Tx CH] channel. For the parameters that can be assigned, refer to “Parameter, die Controllern zugewiesen werden konnen” on page 270. Control Change messages are not used for transmission to M7CL Editor because there is no guarantee that the contents of the assignment tables will match. (Parameter Change messages are always used.) Control Change numbers 0 and 32 are for selecting banks. STATUS 1011nnnn Bn Control change DATA 00 Control number (00) 0vvvvvvv vv Control Value (0-127) STATUS 1011nnnn Bn Control change DATA 20 Control number (32) 0vvvvvvv vv Control Value (0-127) If [TABLE] is selected STATUS 1011nnnn Bn Control change DATA 0nnnnnnn nn Control number (1-5, 7-31, 33-37, 38-95, 102-119) * 0vvvvvvv vv Control Value (0-127) * Numbers 0, 32, and 96–101 cannot be used. * Control number 6, 38 can be used. Equation for converting a Control Value to parameter data paramSteps = paramMax - paramMin + 1; add = paramWidth / paramSteps; mod = paramWidth - add * paramSteps; curValue = paramSteps * add + mod / 2; (1) If the assigned parameter has fewer than 128 steps paramWidth = 128; rxValue = Control value; (2) If the assigned parameter has 128 or more but less than 16,384 steps paramWidth = 16384; (2-1) When High and Low data is received rxValue = Control value(High) * 128 + Control value(Low); (2-2) When only Low data is received rxValue = (curValue & 16256) + Control value(Low); (2-3) When only High data is received rxValue = Control value(High) * 128 + (curValue & 127); (3) If the assigned parameter has 16,384 or more but less than 2,097,152 steps paramWidth = 2097152; (3-1) When High, Middle, and Low data is received rxValue = Control value(High) * 16384 + Control value(Middle) * 128 + Control value(Low); (3-2) When only Low data is received rxValue = (curValue & 2097024) + Control value(Low); (3-3) When only Middle data is received rxValue = (curValue & 2080895) + Control value...
Ce manuel est également adapté pour les modèles :Instruments de musique - M7CL-48 (16.68 mb)
Instruments de musique - M7CL-48ES (16.68 mb)